Preventing connections to unsecured wireless access points

Anonymous
2015-05-28T11:13:57+00:00

My Acer laptop has a somewhat weak Qualcomm network card, and the location I use it from in the house tends to have an average signal strength at best. 

There is another, unsecured wireless access points accessible in the area, which I can't use because it requires login credentials from a browser. Sometimes, Windows automatically switches me on to this access point. 

I should point out that my own Access Point is set to "Connect Automatically", while the unsecured one is not. Yet this still happens. 

Am running fully updated Windows 8.1.

Any workaround or prevention?

Thanks!

Windows for home | Previous Windows versions | Internet and connectivity

Locked Question. This question was migrated from the Microsoft Support Community. You can vote on whether it's helpful, but you can't add comments or replies or follow the question.

0 comments No comments

3 answers

Sort by: Most helpful
  1. Anonymous
    2015-05-29T07:05:54+00:00

    I don't have the Manage wireless networks option in the Network and Sharing Center.

    Was this answer helpful?

    1 person found this answer helpful.
    0 comments No comments
  2. Anonymous
    2015-06-05T09:10:47+00:00

    Hello Alastair,

    Apologies for late response.

    This issue may occur if the Enable IEEE 802.1X authentication for this network check box is selected. If this check box is selected, but there is no server to authenticate against, the connection is disconnected. If you reestablish the wireless network connection, it disconnects again after a short time.

    To disable IEEE 802.1X authentication, follow these steps:

    a. Press "Windows + R" key on the keyboard to open Run window.

    b. Type ncpa.cpl and then hit Enter.

    c. Right-click your wireless network connection, and then clicks Properties.

    d. Click the Wireless Networks tab.

    e. Under Preferred networks, click your wireless network, and then click Properties.

    f. Click the Authentication tab, click to clear the Enable IEEE 802.1X authentication for this network check box, and then click OK two times.

    Hope this helps.

    Was this answer helpful?

    0 comments No comments
  3. Anonymous
    2015-05-29T06:59:56+00:00

    Hi Alastair,

    Thank you for posting your query in Microsoft Community.

    When you are logged on to Windows, your computer can automatically connect to a preferred network (a network that you have previously connected to) that's in range. Sometimes, your computer will continuously switch between two preferred networks, which can cause temporary interruptions to your connection, or your computer might lose the connection entirely.

    When you move around with a mobile computer within a certain area, and you're connected to the Internet or another wireless network, your computer continuously switches from one wireless router or access point to another to stay connected. Even when you're not moving, your computer might sometimes try to switch between routers or access points. This continuous switching can cause temporary interruptions to your connection, or you might lose the connection entirely. Here are some things you can try to stop the continuous switching.

    Here are some things you can try to stop the continuous switching:

    Move your computer closer to one of the networks. With 802.11b or 802.11g routers and access points, the maximum range is up to 150 feet (46 meters) indoors and 300 feet (92 meters) outdoors. With 802.11a routers and access points, the maximum range is 50 feet (15 meters) indoors and 100 feet (30 meters) outdoors. These ranges are in optimal conditions with no interference. Keep them in mind when deciding where to locate your computer.

    Turn off automatic switching in one or both of the network profiles. Here's how to do it:

    a. Press Windows key + X and click Control Panel

    b. Click Network and Internet, click Network and Sharing Center, and then, in the left pane, click Manage wireless networks.

    c. Right-click the network profile that you want to turn off automatic switching, and then click Properties.

    d. Click the Connection tab, clear the Connect to a more preferred network if available check box, and then click OK.

    This will turn off automatic switching.

    You may also refer to: Wired and wireless network problems

    Hope this information is helpful. Please feel free to reply in case you face any other issues with Windows in future.

    Was this answer helpful?

    0 comments No comments