question

ibrahimgamal-9547 avatar image
0 Votes"
ibrahimgamal-9547 asked SunnyNiu-MSFT commented

push SCCM Client or manual install failed after enable Https

84960-capture20233.png


mem-cm-co-management
capture20233.png (191.8 KiB)
5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

SunnyNiu-MSFT avatar image
0 Votes"
SunnyNiu-MSFT answered

@ibrahimgamal-9547
Based on the above description, it is difficult for us to determine the specific cause.
The error means the expected version of Client Package cannot be got from DP.
Here are the things which we could to fix it.

  • SCCM server as an local administrator.
    Make sure our SCCM server should be the part of local administrator.
    85226-1.png


  • Boundary and Boundary group.
    Check boundaries, there could be a case that the client is getting ip address of a new DHCP range which is not added in your boundaries and boundaries group.

  • Distribution Point status.
    Go to Monitoring > Overview > Distribution Status > Distribution Point Configuration Status
    See if there is any errors on very initial level.
    In addition, we could try to update Client Package from Package Node in SCCM Console, then observe the distmgr.log to make sure the updated pkg has been distributed to DP, then try again.

  • Client installation files permission.
    We need to check the permissions on the folder where we keep all client installation files which would be accessed while pushing the clients. Mainly, the service account which we created to install the client should have minimum modify access on it. If we need to test, then add "Everyone" with modify access on sharing and NTFS permission. Then try.

  • Reinstall MP.
    Uninstall Management Point, wait for 10 minutes and then reboot the server.
    Install Management Point again and then try.

  • Reinstall DP.
    Uninstall Distribution Point wait for 10 minutes and then reboot the server.
    Install and configure Distribution Point and then check.


If the response is helpful, please click "Accept Answer"and upvote it.
Note: Please follow the steps in our documentation to enable e-mail notifications if you want to receive the related email notification for this thread.



1.png (8.5 KiB)
5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

ibrahimgamal-9547 avatar image
0 Votes"
ibrahimgamal-9547 answered

first thanks Sunny,
i tried all previous steps but no issue not solved

5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

ibrahimgamal-9547 avatar image
0 Votes"
ibrahimgamal-9547 answered SunnyNiu-MSFT commented

GetDPLocations failed with error 0x87d00454 ccmsetup 4/6/2021 5:05:14 PM 1148 (0x047C)
Failed to get DP locations as the expected version from MP 'HTTPS://SCCM-t.ttt.local'. Error 0x87d00454 ccmsetup 4/6/2021 5:05:14 PM 1148 (0x047C)
Failed to get client version for sending state messages. Error 0x8004100e ccmsetup 4/6/2021 5:05:14 PM 1148 (0x047C)

· 1
5 |1600 characters needed characters left characters exceeded

Up to 10 attachments (including images) can be used with a maximum of 3.0 MiB each and 30.0 MiB total.

Based on this description without context, it is difficult to determine the specific cause. Because this error may also appear during other operations. Therefore, we hope to have more specific log information. We may closely check the CCMSetup.log and ClientMSI.log to get more information about the installation failed reason.

0 Votes 0 ·