Επεξεργασία

Κοινή χρήση μέσω


New-HoldCompliancePolicy

This cmdlet is available only in Security & Compliance PowerShell. For more information, see Security & Compliance PowerShell.

Use the New-HoldCompliancePolicy cmdlet to create new preservation policies in the Microsoft Purview compliance portal.

Note: The New-HoldCompliancePolicy cmdlet has been replaced by the New-RetentionCompliancePolicy cmdlet. If you have scripts that use New-HoldCompliancePolicy, update them to use New-RetentionCompliancePolicy.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

New-HoldCompliancePolicy
   [-Name] <String>
   [-Comment <String>]
   [-Confirm]
   [-Enabled <Boolean>]
   [-ExchangeLocation <MultiValuedProperty>]
   [-Force]
   [-PublicFolderLocation <MultiValuedProperty>]
   [-SharePointLocation <MultiValuedProperty>]
   [-WhatIf]
   [<CommonParameters>]

Description

New policies are not valid and will not be applied until a preservation rule is added to the policy.

To use this cmdlet in Security & Compliance PowerShell, you need to be assigned permissions. For more information, see Permissions in the Microsoft Purview compliance portal.

Examples

Example 1

New-HoldCompliancePolicy -Name "Regulation 123 Compliance" -ExchangeLocation "Kitty Petersen", "Scott Nakamura" -SharePointLocation "https://contoso.sharepoint.com/sites/teams/finance"

This example creates a preservation policy named "Regulation 123 Compliance" for the mailboxes of Kitty Petersen and Scott Nakamura, and the finance SharePoint Online site.

Parameters

-Comment

The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".

Type:String
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-Enabled

The Enabled parameter specifies whether the policy is enabled or disabled. Valid values are:

  • $true: The policy is enabled. This is the default value.
  • $false: The policy is disabled.
Type:Boolean
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-ExchangeLocation

The ExchangeLocation parameter specifies the mailboxes to include in the policy. Valid values are:

  • A mailbox
  • A distribution group or mail-enabled security group (all mailboxes that are currently members of the group).

To specify a mailbox or distribution group, you can use any value that uniquely identifies it. For example:

  • Name
  • Distinguished name (DN)
  • Email address
  • GUID

You can enter multiple values separated by commas. If the values contain spaces or otherwise require quotation marks, use the following syntax: "Value1","Value2",..."ValueN".

If no mailboxes are specified, then no mailboxes are placed on hold.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-Force

The Force switch hides warning or confirmation messages. You don't need to specify a value with this switch.

You can use this switch to run tasks programmatically where prompting for administrative input is inappropriate.

Type:SwitchParameter
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-Name

The Name parameter specifies the unique name of the preservation policy. If the value contains spaces, enclose the value in quotation marks.

Type:String
Position:1
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-PublicFolderLocation

The PublicFolderLocation parameter specifies that you want to include all public folders in the preservation policy. You use the value All for this parameter.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-SharePointLocation

The SharePointLocation parameter specifies the SharePoint Online sites to include. You identify the site by its URL value, or you can use the value All to include all sites.

You can enter multiple values separated by commas. If the values contain spaces or otherwise require quotation marks, use the following syntax: "Value1","Value2",..."ValueN".

SharePoint Online sites can't be added to the policy until they have been indexed. If no sites are specified, then no sites are placed on hold.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance

-WhatIf

The WhatIf switch doesn't work in Security & Compliance PowerShell.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Security & Compliance