Επεξεργασία

Κοινή χρήση μέσω


Resume-Message

This cmdlet is available only in on-premises Exchange.

Use the Resume-Message cmdlet to enable delivery of a previously suspended message in a queue on a Mailbox server or Edge Transport server.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Resume-Message
      -Filter <String>
      [-Server <ServerIdParameter>]
      [-Confirm]
      [-WhatIf]
      [<CommonParameters>]
Resume-Message
      [-Identity] <MessageIdentity>
      [-Confirm]
      [-WhatIf]
      [<CommonParameters>]

Description

A message being sent to multiple recipients might be located in multiple queues. If you specify an Identity parameter, the message is resumed in a single queue if that identity matches only a single message. If the identity matches more than one message, you receive an error. To resume a message in more than one queue in a single operation, you must use the Filter parameter.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Resume-Message -Server Server1 -Filter "FromAddress -eq 'kweku@contoso.com' -and ExpirationTime -lt '1/5/2018 3:00 PM'"

This example resumes delivery of all messages in a suspended state and for which the following conditions are true:

  • The messages were sent by the sender kweku@contoso.com.
  • The messages are queued on the server Server1.
  • The messages will expire before 15:00 on January 5, 2018.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Filter

The Filter parameter specifies one or more messages by using OPATH filter syntax. The OPATH filter includes a message property name followed by a comparison operator and value (for example, "FromAddress -like '*@contoso.com'"). For details about filterable message properties and comparison operators, see Properties of messages in queues and Find queues and messages in queues in the Exchange Management Shell.

You can specify multiple criteria by using the and comparison operator. Property values that aren't expressed as an integer must be enclosed in quotation marks (").

Type:String
Position:Named
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Identity

The Identity parameter specifies the message. Valid input for this parameter uses the syntax Server\Queue\MessageInteger or Queue\MessageInteger or MessageInteger, for example, Mailbox01\contoso.com\5 or 10. For details about message identity, see Message identity.

Type:MessageIdentity
Position:1
Default value:None
Required:True
Accept pipeline input:True
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Server

The Server parameter specifies the Exchange server where you want to run this command. You can use any value that uniquely identifies the server. For example:

  • Name
  • FQDN
  • Distinguished name (DN)
  • Exchange Legacy DN

If you don't use this parameter, the command is run on the local server.

You can use the Server parameter and the Filter parameter in the same command. You can't use the Server parameter and the Identity parameter in the same command.

Type:ServerIdParameter
Position:Named
Default value:None
Required:False
Accept pipeline input:True
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.