ATI RADEON HD 2400XT DRIVER VER 8.970.100.9001

Hi,

Since you would like to have the Driver Version 8.970.100.9001 ATI Radeon HD 2400 XT, you may check this link and manually select your driver.

Let us know if you need further help.

Today, December 19th, 2017, Microsoft reversed their idiotic move from November 24, 2017 that depreciated the driver for ATI Radeon HD2400XT Dual monitor display adapter.

After an update started, I left that computer for a while as I did other things.  In about an hour, I returned to the single monitor in LoRes mode just like when the ATI driver was uninstalled and the Windows Basic Video Driver installed in it's place.  I did not know what to expect this time, but I went to the Display Settings and set the resolution back to the maximum and tried to detect additional monitors, which were not found.  

So I went to the Device Manager and it still showed the MS Driver.  I did a right click and did a scan - noting changed, so I started the search for an updated video driver.  This time the search came up with the HD2400XT driver and installed it.  Now the Device Manage showed the proper card and the original driver from 2013 that had been there before.  

Now, the 2nd monitor was detected and I started reseting my "new" monitor to what it had been for years through XP, Win 7 and Win 10 (all versions).  Life is good till MS decides to make another bone head change without notice.

Problemas con la pantalla

Hi,

Based on the details provided, there are a lot of possible factors for this matter to occur. We recommend that you perform these methods of troubleshooting and see if there are any changes:

Run Hardware and Device troubleshooter.

To run the troubleshooter, follow these steps:

1. On the search bar, type Troubleshooting and hit Enter.
2. Choose Hardware and Sound.
3. Click on Hardware and Devices to run the troubleshooter.

Run SFC Scan.

System File Checker will scan and run an automatic repair to any corrupted system files that it will detect. We suggest that you perform it twice or thrice. To run an SFC scan, follow these steps:       

1. Run Command Prompt as Administrator.
2. Type sfc /scannow and hit Enter.

Run DISM Tool.

To perform DISM, follow these steps:       

1. Run Command Prompt as Administrator.
2. Type the following command:       
   1. DISM.exe /Online /Cleanup-image /scanhealth
   2. DISM.exe /Online /Cleanup-image /Restorehealth

NOTE: This might take a while to finish scanning. Do not cancel.

For more information regarding SFC and DISM Tool, click here.

Clean Boot.

To perform a Clean Boot, click here.

Note: Reset the computer back to Normal Mode once you are done with the troubleshooting by following the section "How to reset the computer to start normally after clean boot troubleshooting" from the same article.

If the issue persists, it is possible that the issue hardware itself. We recommend that you contact your manufacturer for further assistance.

Let us know how it goes.

Regards.

Sorry. The solution did not work.

Also tried out in safe mode deleted the driver and reinstalled it but no improvement.

Tried out all the techniques and tricks as available on the net but no success.

Also reduced the refresh rate and reduced the resolution but no success.

I am determined not to replace the video card and will keep trying and would appreciate any suggestions to rectify this.

This morning as every morning when I started the computer, it boots up and mid way when the win10 logo is about to come, one of the monitors(the primary one)drops off and goes into power save mode with the other in blue and after some time I get the watchdog message with TDR VIDEO failure.

This is after the update only.I currently have"2017-10 Cumulative Update for Windows 10 Version 1703 for x64-based Systems (KB4041676)" & "2017-10 Security Update for Adobe Flash Player for Windows 10 Version 1703 for x64-based Systems (KB4049179)"as the latest update downloaded.

Well would appreciate a helpful and resolvable assistance and solution.

regards