Edit

Share via

Configure the time mechanism for Active Directory Windows Virtual Machines in Azure

  • Article

Applies to: ✔️ Windows Virtual Machines

Use this guide to learn how to set up time synchronization for your Azure Windows Virtual Machines that belong to an Active Directory Domain.

Time sync hierarchy in Active Directory Domain Services

Time synchronization in Active Directory should be managed by only allowing the PDC to access an external time source or NTP Server.

All other Domain Controllers would then sync time against the PDC, and all other members will get their time from the Domain Controller that satisfied that member's authentication request.

If you have an Active Directory domain running on virtual machines hosted in Azure, follow these steps to properly set up Time Sync.

Note

This guide focuses on using the Group Policy Management console to perform the configuration. You can achieve the same results by using the Command Prompt, PowerShell, or by manually modifying the Registry; however, those methods are not in scope in this article.

GPO to allow the PDC to synchronize with an External NTP Source

To check current time source in your PDC, from an elevated command prompt run w32tm /query /source and note the output for later comparison.

  1. From Start run gpmc.msc.
  2. Browse to the Forest and Domain where you want to create the GPO.
  3. Create a new GPO, for example PDC Time Sync, in the container Group Policy Objects.
  4. Right-click on the newly created GPO and Edit.
  5. Navigate to the Global Configuration Settings policy under Computer Configuration -> Administrative Templates -> System -> Windows Time Service.
  6. Set it to Enabled and configure the AnnounceFlags parameter to 5.
  7. Navigate to Computer Configuration -> Administrative Templates -> System -> Windows Time Service -> Time Providers.
  8. Double click the Configure Windows NTP Client policy and set it to Enabled, configure the parameter NTPServer to point to an IP address or FQDN of a time server followed by ,0x9 for example: 131.107.13.100,0x9 and configure Type to NTP. For all the other parameters you can use the default values, or use custom ones according to your corporate needs.
  9. Click the Next Setting button, set the Enable Windows NTP Client policy to Enabled and click OK
  10. In the Scope tab of the newly created GPO navigate to Security Filtering and highlight the Authenticated Users group -> Click the Remove button -> OK -> OK
  11. Create a WMI Filter to dynamically get the Domain Controller that holds the PDC role:
    • In the Group Policy Management console, navigate to WMI Filters, right-click on it and select New.
    • In the New WMI Filter window, give a name to the new filter, for example, Get PDC Emulator -> Fill out the Description field (optional) -> Click the Add button.
    • In the WMI Query window leave the Namespace as is, in the Query text box paste the following string Select * from Win32_ComputerSystem where DomainRole = 5, then click the OK button.
    • Back in the New WMI Filter window click the Save button.
  12. In the Scope tab of the newly created GPO navigate to the WMI Filtering drop-down menu and select the previously created WMI filter then click OK.
  13. In the Scope tab of the newly created GPO navigate to the Security Filtering click the Add button and browse for the Domain Controllers group, then click the OK button.
  14. Link the GPO to the Domain Controllers Organizational Unit.

Note

It can take up to 15 minutes for these changes to be reflected by the system.

From an elevated command prompt rerun w32tm /query /source and compare the output to the one you noted at the beginning of the configuration. Now it will be set to the NTP Server you chose.

Tip

If you want to speed-up the process of changing the NTP source on your PDC, from an elevated command prompt run gpupdate /force, followed by w32tm /resync /nowait, then rerun w32tm /query /source; the output should be the NTP Server you used in the above GPO.

GPO for Members

Usually, NTP in Active Directory Domain Services will follow the AD DS Time Hierarchy mentioned at the beginning of this article and no further configuration is required.

Nevertheless, virtual machines hosted in Azure have specific security settings applied to them directly by the Cloud platform.

For all other domain members that are not Domain Controllers, you will need to modify the registry and set the value to 0 in the key Enabled under HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\VMICTimeProvider

Important

Remember that serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully and test them on a couple of test virtual machines to make sure you will get the expected outcome. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For how to back up and restore the Windows Registry follow the steps below.

Back up the Registry

  1. From Start type regedit.exe, and then press Enter. If you are prompted for an administrator password or for confirmation, type the password or provide confirmation.
  2. In the Registry Editor window, locate and click the registry key or subkey that you want to back up.
  3. From the File menu select Export.
  4. In the Export Registry File dialog box, select the location to which you want to save the backup copy, type a name for the backup file in the File name field, and then click Save.

Restore a Registry backup

  1. From Start type regedit.exe, and then press Enter. If you are prompted for an administrator password or for confirmation, type the password or provide confirmation.
  2. In the Registry Editor window, from the File menu select Import.
  3. In the Import Registry File dialog box, select the location to which you saved the backup copy, select the backup file, and then click Open.

GPO to disable the VMICTimeProvider

Configure the following Group Policy Object to enable domain members to synchronize time with Domain Controllers in their corresponding Active Directory Site:

To check current time source, login to any domain member and from an elevated command prompt run w32tm /query /source and note the output for later comparison.

  1. From a Domain Controller go to Start run gpmc.msc.
  2. Browse to the Forest and Domain where you want to create the GPO.
  3. Create a new GPO, for example Clients Time Sync, in the container Group Policy Objects.
  4. Right-click on the newly created GPO and Edit.
  5. Navigate to Computer Configuration -> Preferences -> Windows Settings -> Right-click on Registry -> New -> Registry Item
  6. In the New Registry Properties window set the following values:
    • On Action: Update
    • On Hive: HKEY_LOCAL_MACHINE
    • On Key Path: browse to SYSTEM\CurrentControlSet\Services\W32Time\TimeProviders\VMICTimeProvider
    • On Value Name type Enabled
    • On Value Type: REG_DWORD
    • On Value Data: type 0
  7. For all the other parameters use the default values and click OK
  8. Link the GPO to the Organizational Unit where your members are located.
  9. Wait or manually force a Group Policy Update on the domain member.

Go back to the domain member and from an elevated command prompt rerun w32tm /query /source and compare the output to the one you noted at the beginning of the configuration. Now it will be set to the Domain Controller that satisfied the member's authentication request.

Next steps

Below are links to more details about the time sync: