New-DeviceTenantPolicy
This cmdlet is available only in Security & Compliance PowerShell. For more information, see Security & Compliance PowerShell.
Use the New-DeviceTenantPolicy cmdlet to create your organization's mobile device tenant policy in Basic Mobility and Security in Microsoft 365.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
New-DeviceTenantPolicy
[-Comment <String>]
[-Confirm]
[-Enabled <Boolean>]
[-Force]
[-WhatIf]
[<CommonParameters>] Description
The cmdlets in Basic Mobility and Security are described in the following list:
- DeviceTenantPolicy and DeviceTenantRule cmdlets: A policy that defines whether to block or allow mobile device access to Exchange Online email by unsupported devices that use Exchange ActiveSync only. This setting applies to all users in your organization. Both allow and block scenarios allow reporting for unsupported devices, and you can specify exceptions to the policy based on security groups.
- DeviceConditionalAccessPolicy and DeviceConditionalAccessRule cmdlets: Policies that control mobile device access to Microsoft 365 for supported devices. These policies are applied to security groups. Unsupported devices are not allowed to enroll in Basic Mobility and Security.
- DeviceConfigurationPolicy and DeviceConfigurationRule cmdlets: Policies that control mobile device settings for supported devices. These policies are applied to security groups.
- Get-DevicePolicy: Returns all Basic Mobility and Security policies regardless of type (DeviceTenantPolicy, DeviceConditionalAccessPolicy or DeviceConfigurationPolicy).
For more information about Basic Mobility and Security, see Overview of Basic Mobility and Security for Microsoft 365.
To use this cmdlet in Security & Compliance PowerShell, you need to be assigned permissions. For more information, see Permissions in the Microsoft Defender portal or Permissions in the Microsoft Purview compliance portal.
Examples
Example 1
New-DeviceTenantPolicyThis example creates your organization's mobile device tenant policy. You can have only one mobile device tenant policy in your organization.
Parameters
-Comment
The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".
| Type: | String |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Confirm
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
| Type: | SwitchParameter |
| Aliases: | cf |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Enabled
The Enabled parameter specifies whether the policy is enabled. Valid values are:
- $true: The policy is enabled. This is the default value.
- $false: The policy is disabled.
| Type: | Boolean |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Force
The Force switch hides warning or confirmation messages. You don't need to specify a value with this switch.
You can use this switch to run tasks programmatically where prompting for administrative input is inappropriate.
| Type: | SwitchParameter |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-WhatIf
The WhatIf switch doesn't work in Security & Compliance PowerShell.
| Type: | SwitchParameter |
| Aliases: | wi |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |