MIPS Error Messages 526-610 (Windows CE 5.0)
The following table shows MIPS error messages number 526 through 610.
| No. | Severity | Message text |
|---|---|---|
| C2526 | ERROR | Code can only be placed in text |
| C2527 | ERROR | Bad instruction opcode |
| C2528 | INFO | Preparing gp-tables |
| C2529 | INFO | Building gp-tables |
| C2530 | ERROR | Label referenced but not defined: %s |
| C2531 | ERROR | Not all branch-label symbols were defined |
| C2532 | ERROR | C0 opcode must be inside .set noreorder section |
| C2533 | ERROR | Byte address of jump target must fit in 28 bits |
| C2534 | ERROR | Jump target is not word-aligned |
| C2536 | ERROR | Register must differ from base |
| C2537 | ERROR | Operand 1 should be fp reg |
| C2538 | ERROR | ulwu instruction not implemented |
| C2539 | ERROR | coproc doubles not implemented |
| C2540 | ERROR | li.e instruction not implemented |
| C2542 | ERROR | Exponent out of range: %s |
| C2543 | ERROR | Only \\""1\\"" or \\""0\\"" allowed left of binary point: %s |
| C2544 | ERROR | Illegally denormalized fraction: %s |
| C2545 | ERROR | Floating point underflow: %s |
| C2546 | ERROR | -M forbidden when assembler runs on a MIPS machine |
| C2547 | ERROR | -M does not support \\"".extended\\"" |
| C2548 | ERROR | -M does not support hex floating point |
| C2549 | ERROR | Floating point literal too long |
| C2550 | ERROR | Too many float literals — compile with \\""-Wb,-nopool\\"" |
| C2551 | ERROR | Cannot label a pseudo-op in text section |
| C2552 | ERROR | Shift amount not 0..31 |
| C2553 | ERROR | Shift amount not 0..63 |
| C2554 | ERROR | gp-relative segments together exceed 64k bytes: %d bytes |
| C2558 | ERROR | MIPS16 move must use a MIPSII gp register |
| C2559 | ERROR | MIPS16 addiu immediate limited to 15 bits |
| C2560 | ERROR | Doubleword opcode not supported by mips2 or earlier |
| C2575 | ERROR | MIPS16 load with symbolic offset must use different base & dest |
| C2576 | ERROR | MIPS16 store may not use symbolic offset in base-offset mode |
| C2577 | ERROR | Non-MIPS16 instruction used in MIPS16 text section |
| C2578 | ERROR | MIPS16 instruction used in non-MIPS16 text section |
| C2579 | ERROR | 2nd register invalid in MIPS16 dsrl and dsra |
| C2580 | ERROR | Branch offset not specified |
| C2581 | ERROR | Relative offset not multiple of 4 |
| C2582 | ERROR | Relative offset beyond 32768 |
| C2583 | ERROR | cprestore offset must be positive and divisible by 4 |
| C2584 | ERROR | .cpalias requires a register argument |
| C2585 | ERROR | Number out of range: %s |
| C2586 | ERROR | MIPS16 general purpose register expected |
| C2587 | ERROR | 2-register MIPS16 jalr must take $ra as first operand |
| C2602 | ERROR | Assembler op/directive expected |
| C2603 | ERROR | Undefined symbol in expression |
| C2604 | ERROR | Invalid symbol in expression: %s |
| C2605 | ERROR | Symbol must have absolute value: %s |
| C2607 | ERROR | No such label |
| C2608 | ERROR | Too many local labels |
| C2609 | ERROR | Overflow |
| C2610 | WARN | Large decimal set sign bit |
See Also
MIPS Technology Guide | MIPS Error Messages 1-525 | MIPS Error Messages 611-660 | MIPS Error Messages 661-910 | MIPS Error Messages 911-980
Send Feedback on this topic to the authors