Controlling a Capture Graph (Windows Embedded CE 6.0)

1/6/2010

The Filter Graph Manager's IMediaControl interface has methods for running, stopping, and pausing the entire graph. If the filter graph has capture and preview streams, however, you probably want to control the two streams independently. For example, you might want to preview the video without capturing it. You can do this through the ICaptureGraphBuilder2::ControlStream method.

Note

This method does not work when capturing to an Advanced Systems Format (ASF) file.

Controlling the Capture Stream

The following code sets the video capture stream to run for four seconds, starting one second after the graph runs:

// Control the video capture stream. 
REFERENCE_TIME rtStart = 10000000, rtStop = 50000000;
const WORD wStartCookie = 1, wStopCookie = 2;  // Arbitrary values.
hr = pBuild->ControlStream(
    &PIN_CATEGORY_CAPTURE, // Pin category.
    &MEDIATYPE_Video,      // Media type.
    pCap,                 // Capture filter.
    &rtStart, &rtStop,     // Start and stop times.
    wStartCookie, wStopCookie  // Values for the start and stop events.
);
pControl->Run();

The first parameter specifies which stream to control, as a pin category GUID. The second parameter gives the media type. The third parameter is a pointer to the capture filter. To control all the capture streams in the graph, set the second and third parameters to NULL.

The next two parameters define the times when the stream will start and stop, relative to the time when the graph starts running. Call IMediaControl::Run to run the graph. Until you run the graph, the ICaptureGraphBuilder2::ControlStream method has no effect. If the graph is already running, the settings take effect immediately.

The last two parameters are used for getting event notifications when the stream starts and stops. For each stream that you control using this method, the filter graph sends a pair of events: EC_STREAM_CONTROL_STARTED when the stream starts, and EC_STREAM_CONTROL_STOPPED when the stream stops. The values of wStartCookie and wStopCookie are used as the second event parameter. Thus, lParam2 in the start event equals wStartCookie, and lParam2 in the stop event equals wStopCookie. The following code shows how to get these events:

while (hr = pEvent->GetEvent(&evCode, &param1, &param2, 0), SUCCEEDED(hr))
{
    switch (evCode)
    {
        case EC_STREAM_CONTROL_STARTED: 
        // param2 == wStartCookie
        break;

        case EC_STREAM_CONTROL_STOPPED: 
        // param2 == wStopCookie
        break;
    } 
    pEvent->FreeEventParams(evCode, param1, param2);
}

The ICaptureGraphBuilder2::ControlStream method defines some special values for the start and stop times.

Value	Start	Stop
MAXLONGLONG	Never start this stream.	Do not stop until the graph stops.
NULL	Start immediately when the graph runs.	Stop immediately.

For example, the following code stops the capture stream immediately:

pBuild->ControlStream(&PIN_CATEGORY_CAPTURE, &MEDIATYPE_Video, pCap,
    0, 0,     // Start and stop times.
    wStartCookie, wStopCookie); 

Although you can stop the capture stream and restart it later, this will create a gap in the time stamps. On playback, the video will appear to stall during the gap (depending on the file format).

Controlling the Preview Stream

To control the preview pin, call ICaptureGraphBuilder2::ControlStream but set the first parameter to PIN_CATEGORY_PREVIEW. This works just like it does for PIN_CATEGORY_CAPTURE, except that you cannot use reference times to specify the start and stop, because the preview frames do not have time stamps. Therefore, you must use NULL or MAXLONGLONG. The following code shows how to use NULL to start the preview stream:

pBuild->ControlStream(&PIN_CATEGORY_PREVIEW, &MEDIATYPE_Video, pCap,
    NULL,    // Start now.
    0,       // (Don't care.)
    wStartCookie, wStopCookie); 

The following code shows how to use MAXLONGLONG to stop the preview stream:

pBuild->ControlStream(&PIN_CATEGORY_PREVIEW, &MEDIATYPE_Video, pCap,
    0,               // (Don't care.)
    MAXLONGLONG,     // Stop now.
    wStartCookie, wStopCookie); 

It does not matter whether the preview stream comes from a preview pin on the capture filter, or from the Smart Tee filter. The ICaptureGraphBuilder2::ControlStream method works either way.

Remarks about Stream Control

The default behavior for a pin is to deliver samples when the graph runs. For example, suppose that you call ICaptureGraphBuilder2::ControlStream with PIN_CATEGORY_CAPTURE but not with PIN_CATEGORY_PREVIEW. When you run the graph, the preview stream will run immediately, while the capture stream will run at whatever time you specified in ICaptureGraphBuilder2::ControlStream.

If you are capturing more than one stream and sending them to a mux filter — for example, if you are capturing audio and video to an AVI file — you should control both streams in tandem. Otherwise, the mux filter might block waiting for one stream, as it tries to interleave the two streams. Set the same start and stop times on all capture streams before running the graph:

pBuild->ControlStream(&PIN_CATEGORY_CAPTURE, 
    NULL, NULL,       // All capture streams.
    &rtStart, rtStop, 
    wStartCookie, wStopCookie); 

Internally, the ICaptureGraphBuilder2::ControlStream method uses the IAMStreamControl Interface, which is exposed on the pins of the capture filter, the Smart Tee filter (if present), and possibly the mux filter. You can use this interface directly, instead of calling ICaptureGraphBuilder2::ControlStream, although there is no particular advantage to doing so.

See Also

Concepts

Video Capture