Configure NPS on a Multihomed Computer
Applies To: Windows Server 2008
Configure NPS on a multihomed computer
When you use multiple network adapters in a server running Network Policy Server (NPS), you can configure the following:
The network adapters that do and do not send and receive RADIUS traffic.
On a per-network adapter basis, whether NPS monitors RADIUS traffic on Internet Protocol version 4 (IPv4), IPv6, or both IPv4 and IPv6.
The UDP port numbers over which RADIUS traffic is sent and received on a per-protocol (IPv4 or IPv6), per-network adapter basis.
By default, NPS listens for RADIUS traffic on ports 1812, 1813, 1645, and 1646 for both IPv6 and IPv4 for all installed network adapters. Because NPS automatically uses all network adapters for RADIUS traffic, you only need to specify the network adapters that you want NPS to use for RADIUS traffic when you want to prevent NPS from using an adapter for RADIUS traffic.
If you uninstall either IPv4 or IPv6 on a network adapter, NPS does not monitor RADIUS traffic for the uninstalled protocol.
On an NPS server that has multiple network adapters installed, you might want to configure NPS to send and receive RADIUS traffic only on an adapter you specify.
For example, one network adapter installed in the NPS server might lead to a network segment that does not contain RADIUS clients, while a second network adapter provides NPS with a network path to its configured RADIUS clients. In this scenario, it is important to direct NPS to use the second network adapter for all RADIUS traffic.
In another example, if your NPS server has three network adapters installed, but you only want NPS to use two of the adapters for RADIUS traffic, you should configure port information for the two adapters only. By excluding port configuration for the third adapter, you prevent NPS from using the adapter for RADIUS traffic.
Using a network adapter
To configure NPS to listen for and send RADIUS traffic on a network adapter, use the following syntax:
IPv4 traffic syntax: IPAddress:UDPport, where IPAddress is the IPv4 address that is configured on the network adapter over which you want to send RADIUS traffic, and UDPport is the RADIUS port number that you want to use for RADIUS authentication or accounting traffic.
IPv6 traffic syntax: [IPv6Address]:UDPport, where the brackets around IPv6Address are required, IPv6Address is the IPv6 address that is configured on the network adapter over which you want to send RADIUS traffic, and UDPport is the RADIUS port number that you want to use for RADIUS authentication or accounting traffic.
The following characters can be used as delimiters for configuring IP address and UDP port information:
Address/port delimiter: colon (:)
Port delimiter: comma (,)
Interface delimiter: semicolon (;)
Configuring network access servers
Make sure that your network access servers are configured with the same RADIUS UDP port numbers that you configure on your NPS servers. The RADIUS standard UDP ports defined in RFCs 2865 and 2866 are 1812 for authentication and 1813 for accounting; however, some access servers are configured by default to use UDP port 1645 for authentication requests and UDP port 1646 for accounting requests.
If you do not use the RADIUS default port numbers, you must configure exceptions on the firewall for the local computer to allow RADIUS traffic on the new ports. For more information, see NPS and Firewalls.
Membership in Domain Admins, or equivalent, is the minimum required to complete this procedure.
To specify the network adapter and UDP ports that NPS uses for RADIUS traffic
Open the NPS console.
Right-click Network Policy Server, and then click Properties.
Click the Ports tab, and prepend the IP address for the network adapter you want to use for RADIUS traffic to the existing port numbers. For example, if you want to use the IP address 192.168.1.2 and RADIUS ports 1812 and 1645 for authentication requests, change the port setting from 1812,1645 to 192.168.1.2:1812,1645.
If your RADIUS authentication and RADIUS accounting UDP ports are different from the default values, change the port settings accordingly.
To use multiple port settings for authentication or accounting requests, separate the port numbers with commas.