Applies to: Windows Server 2022, Windows Server 2019, Windows Server 2016, Windows Server 2012 R2, Windows Server 2012
Provides information about network latency and network loss at intermediate hops between a source and destination. This command sends multiple echo Request messages to each router between a source and destination, over a period of time, and then computes results based on the packets returned from each router. Because this command displays the degree of packet loss at any given router or link, you can determine which routers or subnets might be having network problems. Used without parameters, this command displays help.
This command is available only if the Internet Protocol (TCP/IP) protocol is installed as a component in the properties of a network adapter in Network Connections.
Additionally, this command identifies which routers are on the path, same as using the tracert command. Howevever, this command also sends pings periodically to all of the routers over a specified time period and computes statistics based on the number returned from each.
pathping [/n] [/h <maximumhops>] [/g <hostlist>] [/p <Period>] [/q <numqueries> [/w <timeout>] [/i <IPaddress>] [/4 <IPv4>] [/6 <IPv6>][<targetname>]
|/n||Prevents pathping from attempting to resolve the IP addresses of intermediate routers to their names. This might expedite the display of pathping results.|
||Specifies the maximum number of hops in the path to search for the target (destination). The default is 30 hops.|
||Specifies that the echo Request messages use the Loose Source Route option in the IP header with the set of intermediate destinations specified in hostlist. With loose source routing, successive intermediate destinations can be separated by one or multiple routers. The maximum number of addresses or names in the host list is 9. The hostlist is a series of IP addresses (in dotted decimal notation) separated by spaces.|
||Specifies the number of milliseconds to wait between consecutive pings. The default is 250 milliseconds (1/4 second). This parameter sends individual pings to each intermediate hop. Because of this, the interval between two pings sent to the same hop is period multiplied by the number of hops.|
||Specifies the number of echo Request messages sent to each router in the path. The default is 100 queries.|
||Specifies the number of milliseconds to wait for each reply. The default is 3000 milliseconds (3 seconds). This parameter sends multiple pings in parallel. Because of this, the amount of time specified in the timeout parameter isn't bounded by the amount of time specified in the period parameter for waiting between pings.|
||Specifies the source address.|
||Specifies that pathping uses IPv4 only.|
||Specifies that pathping uses IPv6 only.|
||Specifies the destination, which is identified either by IP address or host name.|
|/?||Displays help at the command prompt.|
All parameters are case-sensitive.
To avoid network congestion and to minimize the effects of burst losses, pings should be sent at a sufficiently slow pace.
Example of the pathping command output
D:\>pathping /n contoso1 Tracing route to contoso1 [10.54.1.196] over a maximum of 30 hops: 0 172.16.87.35 1 172.16.87.218 2 192.168.52.1 3 192.168.80.1 4 10.54.247.14 5 10.54.1.196 computing statistics for 125 seconds... Source to Here This Node/Link Hop RTT Lost/Sent = Pct Lost/Sent = Pct address 0 172.16.87.35 0/ 100 = 0% | 1 41ms 0/ 100 = 0% 0/ 100 = 0% 172.16.87.218 13/ 100 = 13% | 2 22ms 16/ 100 = 16% 3/ 100 = 3% 192.168.52.1 0/ 100 = 0% | 3 24ms 13/ 100 = 13% 0/ 100 = 0% 192.168.80.1 0/ 100 = 0% | 4 21ms 14/ 100 = 14% 1/ 100 = 1% 10.54.247.14 0/ 100 = 0% | 5 24ms 13/ 100 = 13% 0/ 100 = 0% 10.54.1.196 Trace complete.
When pathping is run, the first results list the path. Next, a busy message is displayed for approximately 90 seconds (the time varies by hop count). During this time, information is gathered from all routers previously listed and from the links between them. At the end of this period, the test results are displayed.
In the above sample report, the This Node/Link, Lost/Sent = Pct and address columns show that the link between 172.16.87.218 and 192.168.52.1 is dropping 13% of the packets. The routers at hops 2 and 4 are also dropping packets addressed to them, but this loss doesn't affect their ability to forward traffic that isn't addressed to them.
The loss rates displayed for the links, identified as a vertical bar (|) in the address column, indicate link congestion that is causing the loss of packets that are being forwarded on the path. The loss rates displayed for routers (identified by their IP addresses) indicate that these routers might be overloaded.
Submit and view feedback for