Condividi tramite

Managing Battery Life and Power Consumption Overview

  • Articolo

Applies To: Windows 8, Windows 8.1, Windows Server 2008 R2, Windows Server 2012, Windows Server 2012 R2

Windows®-based laptops must meet energy-efficiency regulatory requirements, such as the United States Environmental Protection Agency (EPA) Energy Star program. Furthermore, surveys have shown that longer battery life for laptops continues to be a leading request from consumers.

Hardware and software factors such as a low-capacity battery, a processor-intensive driver, or a poorly configured power setting can cause a significant reduction in battery life. When you design your system, you should experiment with multiple configurations of each of these factors to find the best balance of battery life and performance.

Hardware

This section lists a few of the common hardware design considerations that can affect battery life.

  • Battery capacity. Check with your battery manufacturer to determine the battery capacity.

  • Other hardware components. Ask your hardware component manufacturers for power-consumption test results for each hardware component.

For information on each of these battery-life factors, see Mobile Battery Life Solutions: A Guide for Mobile Platform Professionals.

Software

This section lists a few of the common software design considerations that can affect battery life.

  • Drivers. As you add each new driver to the system, observe the driver's impact on power consumption. A single poorly performing driver can greatly affect system performance.

  • Applications, services, and other software. As you add each new software application to the system, observe the application's impact on power consumption. A single poorly performing application can greatly affect system performance.

  • Windows power policy settings. Optimize Windows power policy settings to balance performance needs and battery life. For more information, see the section: Windows Power Policy Settings .

For more information about each of these battery life factors, see Mobile Battery Life Solutions: A Guide for Mobile Platform Professionals.

Windows Power Policy Settings

This section lists a few of the common configurable settings that can affect battery life. Test these and other settings to create an optimal power plan for your system.

Settings can be specific to whether the computer is plugged in (AC) or on battery power (DC). You can configure the following settings:

  • Display brightness

    The most effective way to reduce the power consumption on a mobile computer when the display is in use is to reduce the display brightness. The attached display is the largest power consumer. The display uses up to 40 percent of the overall system power consumption.

    By default, Windows significantly reduces the display brightness when a mobile computer is on battery power. Depending on your hardware and the needs of your users, you can adjust the default display brightness setting lower to increase battery life, or higher to make the display easier to read.

  • Display timeout

    Mobile PC battery life can be significantly extended by using a short display idle timeout.

Note

Display dimming: Mobile computers that run Windows 8.1 and Windows Server 2012 R2 will dim the display 15 seconds before the Display timeout. This value is no longer configurable.

  • Hard disk timeout

    Although the hard disk drive is not the primary power consumer in the typical mobile computer, you may be able to save power by increasing the hard drive timeout.

    When the hard drive is idle for a period of time, the hard drive's motor stops. The next time that the computer needs to access the hard drive, the system response may be slow while the hard drive begins to spin again.

    Depending on your hardware and the needs of your users, you can adjust the default hard disk timeout lower to increase battery life, or higher to increase the availability of the hard disk.

  • Sleep mode

    By default, if the processor is idle, and the end user is not using the computer, Windows enters low-power sleep mode or hibernate mode. The next time that the computer needs processor power, system response may be slow while the processor recovers.

    Depending on your hardware and the needs of your users, you can adjust the default sleep timer lower to increase battery life, or higher to increase the availability of the processor.

  • Wireless adapter power-save modes

    By default, Windows configures the 802.11 power-save mode to Maximum Performance for both AC and battery power. This configuration keeps the wireless adapter active, even when data is not being transferred. This alleviates compatibility problems between some wireless adapters and access points that are not compatible with 802.11 power-save modes.

    If you create custom power policies to save more power and help extend battery life, consult with the manufacturer of the wireless adapter about the effects of changing the power policy value to Maximum Power Saving or Medium Power Saving.

You can manually modify the power settings for each built-in power configuration. To learn more about these settings and other common configurable power settings, see Mobile Battery Life Solutions: A Guide for Mobile Platform Professionals and Power Policy Configuration and Deployment in Windows.

See Also

Tasks

Set the Default Power Plan
Create a Custom Power Plan

Other Resources

Mobile Battery Life Solutions: A Guide for Mobile Platform Professionals
Windows Performance Toolkit
Power Policy Configuration and Deployment in Windows