What's new for Direct Routing
This article describes what's new in Direct Routing. Check back often for updates.
Network Effectiveness Ratio (NER) metric update
To improve the experience with visibility of possible issues affecting your Direct Routing reliability, we are updating the formula to calculate the metric for Network Effectiveness Ratio (NER). Starting from November 11, 2024, you might notice a slight change in the reported NER for your trunks in the Teams Admin Center (TAC). If you notice a drop in the NER value, you can identify the cause of a call failure by looking at specific response codes. For a list of the most common errors and suggested actions to resolve them, see Microsoft and SIP response codes.
New Survivable Branch Appliance version (v2024.8.15.1) is available
New Survivable Branch Appliance (SBA) for Direct Routing version is available starting September 23, 2024. Latest version supports following functionality:
- Making PSTN calls through the local SBA/SBC with media flowing through the SBC.
- Receiving PSTN calls through the local SBA/SBC with media flowing through the SBC.
- Hold and resume of PSTN calls.
- Blind transfer.
- Call forwarding to a single phone number or Teams user.
- Unanswered call forwarding to single phone number or Teams user.
- Redirect of incoming PSTN call to a Call queue or Auto attendant number to a local agent.
- Redirect of incoming PSTN call to a Call queue or Auto attendant number to an alternative Call queue or Auto attendant number.
- VoIP Fallback. If a VoIP call can't be initiated and the receiving party has a PSTN number, a PSTN call is attempted.
- VoIP calls between local users. If both users are registered behind the same SBA, a VoIP call can be initiated instead of PSTN call, and the SBA supports the call. To get the latest version, contact your SBC vendor. For the list of supported SBC vendors, refer to Session Border Controller configuration. To learn more about Survivable Branch Appliance (SBA), see Survivable Branch Appliance (SBA) for Direct Routing.
SBC certificates EKU extensions test
On March 5, 2024 (starting 9 AM UTC), Microsoft will conduct a 24-hour test of its infrastructure. During this time, Session Border Controllers (SBCs) certificates are required to include both Client and Server Authentication for their Extended Key Usage (EKU) extensions. We kindly ask that you ensure that the EKU extension of your certificate includes Server Authentication and Client Authentication to avoid any service degradation.
If your SBC's certificate EKU extension doesn't include both Server and Client Authentication, your SBCs won't connect with Microsoft infrastructure.
Note that the final switch to request both Server and Client authentication for EKU will be performed on March 19, 2024.
For more information, see Public trusted certificate for the SBC.
SIP certificate to MSPKI Certificate Authority change in DoD and GCCH clouds
Microsoft 365 is updating services powering messaging, meetings, telephony, voice, and video to use TLS certificates from a different set of Root Certificate Authorities (CAs). Affected endpoints include Microsoft Teams Direct Routing SIP endpoints used for PSTN traffic in Office 365 Government - GCC High (GCCH) and DoD deployments. The transition to certificates issued by the new CA for SIP endpoints begins in May 2024. This means that action needs to be taken before end of April 2024.
The new Root CA "DigiCert Global Root G2" is widely trusted by operating systems including Windows, macOS, Android, and iOS and by browsers such as Microsoft Edge, Chrome, Safari, and Firefox. However, it's likely that your SBC has a certificate root store that is manually configured. If so, then the YOUR SBC CA STORE NEEDS TO BE UPDATED TO INCLUDE THE NEW CA TO AVOID SERVICE IMPACT. SBCs that don't have the new Root CA in their list of acceptable CAs receive certificate validation errors, which may impact the availability or function of the service. Both the old and the new CA MUST be trusted by the SBC – Do not remove the old CA. Refer to SBC vendor documentation on how to update the accepted certificate list on your SBC. Both the old and new root certificates need to be trusted by the SBC. Today, the TLS certificates used by Microsoft SIP interfaces chain up to the following Root CA:
Common Name of the CA: DigiCert Global Root CA Thumbprint (SHA1): a8985d3a65e5e5c4b2d7d66d40c6dd2fb19c5436 The old CA certificate can be downloaded directly from DigiCert: http://cacerts.digicert.com/DigiCertGlobalRootCA.crt
New TLS certificates used by Microsoft SIP interfaces will now chain up to the following Root CA: Common Name of the CA: DigiCert Global Root G2 Thumbprint (SHA1): df3c24f9bfd666761b268073fe06d1cc8d4f82a4 The new CA certificate can be downloaded directly from DigiCert: https://cacerts.digicert.com/DigiCertGlobalRootG2.crt
For more details, refer to the technical guidance at https://docs.microsoft.com/en-us/microsoft-365/compliance/encryption-office-365-tls-certificates-changes?view=o365-worldwide To test and confirm your SBCs certificate configuration prior to the change, Microsoft has prepared a testing endpoint that can be used to verify that SBC appliances trust certificates issued from the new root CA (DigiCert Global Root G2). If your SBC can establish a TLS connection to this endpoint, then your connectivity to Teams services shouldn't be affected by the change. These endpoints should be used only for SIP OPTIONS ping messages and not for voice traffic. They aren't production endpoints and aren't backed by redundant configuration. This means they'll experience downtime that lasts for several hours—expect about 95% availability.
Test endpoint FQDN for GCCH: x.sip.pstnhub.infra.gov.teams.microsoft.us Port: 5061
Test endpoint FQDN for DoD: x.sip.pstnhub.infra.dod.teams.microsoft.us Port: 5061
SIP certificate final switch to new MSPKI Certificate Authority
Following two tests on September 5 and 19, Microsoft will perform the final switch to the new Certificate Authority (CA) on October 3, starting at 10 AM UTC. All Microsoft SIP endpoints are gradually switched over to use certificates where the certificate chain rolls up to “DigiCert Global Root G2” Certificate Authority (CA).
If your Session Border Controllers (SBCs) aren't properly configured with the new Certificate Authority (CA), your Direct Routing incoming and outgoing calls will fail after the switch. Work with your SBC vendor directly for further guidance on SBC configuration.
The change requirement and test were communicated to Direct Routing customers through Message Center posts as well as Service Health Incidents in the Microsoft Admin Portal (MC540239, TM614271, MC663640, TM674073, MC674729).
SIP certificate to MSPKI Certificate Authority change, extra testing
On September 19 (starting at 4 PM UTC), Microsoft will perform a 24 hour test where all Microsoft SIP endpoints will be switched over to use certificates where the certificate chain will roll up to “DigiCert Global Root G2” Certificate Authority (CA). New Certificate Authority (CA) must be added in your SBC configuration and old Baltimore CA must be retained; don't replace the old CA. If your SBC doesn’t trust this CA, you won't be able to connect to Teams SIP endpoints during the test. The final switch to the new Certificate Authority (CA) will be performed on October 3.
If you’d like to test and confirm your SBCs certificate configuration prior to the change, Microsoft has prepared a testing endpoint that you can use to verify that SBC appliances trust certificates issued from the new root CA (DigiCert Global Root G2). This endpoint should be used only for SIP OPTIONS ping messages and not for voice traffic. If your SBC can establish a TLS connection to this endpoint, then your connectivity to Teams services shouldn't be affected by the change.
Test endpoint FQDN: sip.mspki.pstnhub.microsoft.com
Port: 5061
SIP certificate to MSPKI Certificate Authority change, test
On September 5 (starting at 9 AM UTC), Microsoft will perform a 24-hour test where all Microsoft SIP endpoints will be switched over to use certificates where the certificate chain will roll up to “DigiCert Global Root G2” Certificate Authority (CA). If your SBC doesn’t trust this CA, you might not be able to connect to Teams SIP endpoints.
If you’d like to test and confirm your SBCs certificate configuration prior to the change, Microsoft has prepared a testing endpoint that can be used to verify that SBC appliances trust certificates issued from the new root CA (DigiCert Global Root G2). This endpoint should be used only for SIP OPTIONS ping messages and not for voice traffic. If your SBC can establish a TLS connection to this endpoint, then your connectivity to Teams services shouldn't be affected by the change.
Test endpoint FQDN: sip.mspki.pstnhub.microsoft.com
Port: 5061
SIP certificate to MSPKI Certificate Authority change
Microsoft 365 is updating services powering messaging, meetings, telephony, voice, and video to use TLS certificates from a different set of Root Certificate Authorities (CAs). This change is being made because the current Root CA expires in May 2025. Affected endpoints include all Microsoft SIP endpoints used for PSTN traffic that utilize TLS connectivity. The transition to certificates issued by the new CA begins in late August.
The new Root CA "DigiCert Global Root G2" is widely trusted by operating systems including Windows, macOS, Android, and iOS and by browsers such as Microsoft Edge, Chrome, Safari, and Firefox. However, it's likely that your SBC has a certificate root store that is manually configured, and it needs to be updated. SBCs that don't have the new Root CA in their list of acceptable CAs receive certificate validation errors, which may impact the availability or function of the service. Refer to your SBC vendor documentation on how to update the accepted certificate list on your SBC.
Today, the TLS certificates used by Microsoft SIP interfaces chain up to the following Root CA:
Common Name of the CA: Baltimore CyberTrust Root Thumbprint (SHA1): d4de20d05e66fc53fe1a50882c78db2852cae474
New TLS certificates used by Microsoft SIP interfaces will now chain up to the following Root CA:
Common Name of the CA: DigiCert Global Root G2 Thumbprint (SHA1): df3c24f9bfd666761b268073fe06d1cc8d4f82a4
The new CA certificate can be downloaded directly from DigiCert: DigiCert Global Root G2.
For more information, see Office TLS Certificate Changes
New Direct Routing SIP endpoints
Microsoft introduces new signaling IPs to Teams Direct Routing SIP endpoints. To ensure this change doesn’t affect your service availability, make sure your Session Border Controller and Firewall are configured to use the recommended subnets 52.112.0.0/14 and 52.122.0.0/15 for classification and ACL rules. For more information, see Microsoft 365, Office 365, and Office 365 GCC environments.
Trunk demoting logic based on SIP Options
A new feature based on SIP Options is introduced for trunk health. When enabled in the gateway configuration (see Set-CsOnlinePSTNGateway cmdlet and SendSipOptions parameter), the routing logic for outbound calls demotes trunks that don't send SIP Options periodically (expected period is one SIP Option sent by the SBC per minute) to the Microsoft backend. These demoted trunks are put to the end of trunks list available for the outbound call and are tried last, which potentially decreases the call setup time.
Any trunk enabled for that feature that doesn't send at least one SIP Option within five minutes to any of the Microsoft regional (NOAM, EMEA, APAC, OCEA) SIP Proxies is considered demoted. If a trunk sends SIP Options to only a subset of Microsoft regional SIP Proxies, then these routes are tried first and the rest are demoted.
Note
Any SBC (configured under the customer or carrier tenant with SendSipOptions set to true) not sending SIP OPTIONS will be demoted. Customers who don't want that behavior should set SendSipOptions to false in their SBC configuration. The same applies to carrier trunks where the SBC configuration is either under the carrier or customer tenant. In these cases, when SendSipOptions is set to true, the SBC sends SIP OPTIONS.
SIP support
On June 1, 2022, Microsoft will remove support for sip-all.pstnhub.microsoft.com and sip-all.pstnhub.gov.teams.microsoft.us FQDNs from Direct Routing configuration.
If no actions are taken before June 1, users won't be able to make or receive calls via Direct Routing.
To prevent service impact:
- Use the recommended subnets: (52.112.0.0/14 and 52.120.0.0/14) for any classification or ACL rules.
- Discontinue use of the sip-all FQDN when configuring Session Border Controls for Direct Routing.
For more information, see Plan Direct Routing.
Note
IP ranges presented in this document are specific to Direct Routing and may differ from the ones advised for Teams client.
TLS certificates
Microsoft 365 is updating Teams and other services to use a different set of Root Certificate Authorities (CAs).
For more information and a full list of affected services, see TLS certificate changes to Microsoft 365 services including Microsoft Teams.
Certificate authorities
Beginning February 1, 2022, the Direct Routing SIP interface will only trust certificates signed by Certificate Authorities (CAs) that are part of the Microsoft Trusted Root Certificate Program. Take the following steps to avoid service impact:
- Ensure that your SBC certificate is signed by a CA that is part of the Microsoft Trusted Root Certificate Program.
- Verify that the Extended Key Usage (EKU) extension of your certificate includes "Server Authentication."
For more information about the Microsoft Trusted Root Certificate Program, see Program Requirements - Microsoft Trusted Root Program.
For a Trusted CA list, see Microsoft Included CA Certificate List.
Replace headers
Starting April 2022, Direct Routing rejects SIP requests that have Replaces headers defined. There are no changes to flows where Microsoft sends Replaces header to the Session Border Controller(SBC).
Check your SBC configurations and ensure sure that you aren't using Replaces headers in SIP requests.
TLS1.0 and 1.1
To provide the best-in-class encryption to our customers, Microsoft plans to deprecate Transport Layer Security (TLS) versions 1.0 and 1.1. On April 3, 2022, Microsoft will force TLS1.2 usage for the Direct Routing SIP interface.
To avoid any service impact, ensure that your SBCs are configured to support TLS1.2 and can connect using one of the following cipher suites:
- TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384 i.e. ECDHE-RSA-AES256-GCM-SHA384
- TLS_ECDHE_RSA_WITH_AES_128_GCM_SHA256 i.e. ECDHE-RSA-AES128-GCM-SHA256
- TLS_ECDHE_RSA_WITH_AES_256_CBC_SHA384 i.e. ECDHE-RSA-AES256-SHA384
- TLS_ECDHE_RSA_WITH_AES_128_CBC_SHA256 i.e. ECDHE-RSA-AES128-SHA256