Rediger

Del via

Restore points

  • Artikkel

Restore points are created to let users select a previous system state. Each restore point contains the required information to restore the system to the selected state. Restore points are created before key changes are made to the system.

System Restore automatically manages the disk space that is allocated for restore points. It purges the oldest restore points to make room for new ones. System Restore allocates space based on the size of the hard disk and the version of Windows that the computer runs, as shown in the following table.

Windows version Hard disk size System Restore space
Windows 7 and later versions > 64 GB Up to five percent of total disk space or a maximum of 10 GB, whichever is less
≤ 64 GB Up to three percent of total disk space
Windows Vista Up to 15 percent of the total disk space or a maximum of 30 percent of available disk space, whichever is less
Windows XP >4 GB Up to 12 percent of total disk space

To change the maximum storage limit in Windows XP, use the System item in Control Panel.
< 4 GB Up to 400 MB

Event-triggered restore points

System Restore automatically creates a restore point before any of the following events occur:

  • Application installation (applies only to applications that use a System Restore-compliant installer). If the application installation causes system problems, the user can restore the system to a state that precedes the installation.
  • Windows Update or AutoUpdate installation. Windows Update (previously known as AutoUpdate) automatically downloads and installs Windows updates. Additionally, it provides an easy way for users to manually download and install updates. System Restore creates a restore point before an update is installed, whether automatically or manually.
  • System restore operation. System Restore automatically creates a restore point as a backup before any restore operation starts. For example, assume that a user accidentally restores Windows to an incorrect restore point. To undo that restoration, the user can restore Windows to a restore point that is previous to the first restore point. After Windows has been restored to its initial state, the user can repeat the process, this time selecting the correct restore point.

Scheduled restore points

Users can configure System Restore to create restore points at regular intervals. Users can also manually create and name a restore point at any time from within the System Restore user interface. These restore points are saved and compressed, and are available in the list of restore points.

In Windows 7 and later versions, System Restore creates a scheduled restore point only if no other restore points have been created in the previous seven days. In Windows Vista, System Restore creates a checkpoint every 24 hours if no other restore points were created on that day. In Windows XP, System Restore creates a checkpoint every 24 hours, regardless of other operations.

Known issue: You cannot restore the system to a restore point after you install a Windows 10 update

Consider the following scenario:

  1. You install Windows 10 on a clean computer.
  2. You turn on system protection, and then create a system restore point that is named "R1."
  3. You install one or more Windows 10 updates.
  4. After the updates finish installing, you restore the system to the "R1" restore point.

In this scenario, the system is not restored to the "R1" restore point. Instead, the computer experiences a Stop error (0xc000021a). You restart the computer, but the system cannot return to the Windows desktop.

Cause

This is a known issue in Windows 10.

During the system restore process, Windows temporarily stages the restoration of files that are in use. It then saves the information in the registry. When the computer restarts, it completes the staged operation.

In this situation, Windows restores the catalog files and stages the driver (.sys) files to be restored when the computer restarts. However, when the computer restarts, Windows loads the existing drivers before it restores the later versions of the drivers. Because the driver versions do not match the versions of the restored catalog files, the restart process stops.

Workaround

To recover from the failed restart and continue the restore process

After the failure occurs, restart the computer until it enters the Windows Recovery Environment (WinRE). To do this, you may have to use a hardware restart switch, and you may have to restart multiple times.

In the Windows Recovery Environment:

  1. Select Troubleshoot > Advanced options > More recovery options > Startup settings, and then select Restart now.
  2. In the list of startup settings, select Disable driver signature enforcement.

    Note

    You may have to use the F7 key to select this setting.

  3. Let the startup process continue. When Windows restarts, the system restore process should resume and finish.

These steps restore the computer to its "R1" state.

To recover from the failed restart

To recover from the failed restart and roll back the restore process, follow these steps:

  1. As described in the previous procedure, restart the computer and then enter WinRE.
  2. In the Windows Recovery Environment, select Troubleshoot > Advanced options > System restore, and then select Undo system restore.

These steps return the computer to the state that it was in before you started the restore process.

To restore Windows to a restore point by using WinRE

To start the System Restore wizard on an affected computer, use WinRE instead of the Settings dialog box. To do this, follow these steps:

  1. Select Start > Settings > Update & Security > Recovery.
  2. Under Advanced options, select Restart now.
  3. After WinRE starts, select Troubleshoot > Advanced options > System restore.
  4. Enter your recovery key as it is shown on the screen, and then follow the instructions in the System Restore wizard.

References

For more information about how to use WinRE, see the following articles: