Aracılığıyla paylaş


Sütun ProductModel.Instructions xml hakkında

The Instructions sütun in the ProductModel tablo stores manufacturing instructions as XML documents.Bu belgeleri, Microsoft Word .NET kullanılarak oluşturulmuştur.

Her bir XML belgesi, belirli bir ürün modeline üretim için tamamlandı yönergeleri içerir.Ancak, her ürün modelinin birkaç ürünü içerebilir.Örneğin, yol 450 bisikleti ürün modeline ' dir.Vardır birkaç bisiklet bu ürün modelinde gibi Yol 450 kırmızı 25 and Yol 450 yeşil 48.Bir ürün modelindeki bisiklet arasındaki birincil fark rengini ve boyutunu ' dir.

Örneğin, SA Sıradağlar çerçeve, LL Sıradağlar çerçeve ve ML Sıradağlar çerçeve belirli ürünler benzersiz bir ürün kimliği ile karşın dağ bisikleti çerçeve ürün modelindeki tüm çerçeve türleri olabilir.

The ProductID sütun in the Product tablo identifies each product.The ProductModelID sütun in the Product identifies the product model to which the product belongs.

Üretim süreci ürün alınan bir iş merkezi başka alır ve XML belgesinin her iş merkezindeki üretim adımları açıklar.Üretim adımları açıklayan araçları, malzeme, mavi yazdırır ve diyagramlarını tüm XML etiketlerini alınmış.Bu nedenle, etiketler sorgulayabilirsiniz.Örneğin, XQuery bir dağ bisikleti üretme olarak kullanılan tüm araçları bulmak için kullanabilirsiniz.

Yazılı bir budur XML sütun.Bu sütun için kullanılan şemalar bu sırasında görüntülenebilir Microsoft Web sitesini.This column uses the AdventureWorksProductModelManuInstructions XML schema.

Örnek XML örneği

Bu örnek, depolanan bir XML örneği, ProductModel.Instructions sütun:

<root xmlns="https://schemas.microsoft.com/sqlserver/2004/07/adventure-works/ProductModelManuInstructions">
  Adventure Works CyclesFR-210B Instructions for Manufacturing HL Touring FrameSummaryThis document contains manufacturing instructions for manufacturing the HL Touring Frame, Product Model 7. Instructions are work center specific and are identified by Work Center ID. These instructions must be followed in the order presented. Deviation from the instructions is not permitted unless an authorized Change Order detailing the deviation is provided by the Engineering Manager. 
<Location LaborHours="2.5" LotSize="100" MachineHours="3" 
          SetupHours="0.5" LocationID="10">
  Work Center - 10 Frame FormingThe following instructions pertain to Work Center 10. (Setup hours = .5, Labor Hours = 2.5, Machine Hours = 3, Lot Sizing = 100) 
  <step>Insert <material>aluminum sheet MS-2341</material> into the 
  <tool>T-85A framing tool</tool>.</step>
  <step>Attach <tool>Trim Jig TJ-26</tool> to the upper and lower right corners of the aluminum sheet. </step>
  <step>Using a <tool>router with a carbide tip 15</tool> 
  , route the aluminum sheet following the jig carefully. </step>
  <step>Insert the frame into <tool>Forming Tool FT-15</tool> and press Start. </step>
  <step> When finished, inspect the forms for defects per Inspection Specification <specs>INFS-111</specs>.</step>
  <step>Remove the frames from the tool and place them in the Completed or Rejected bin as appropriate.</step> 
  </Location>
<Location LaborHours="1.75" LotSize="1" MachineHours="2" SetupHours="0.15" LocationID="20">
  Work Center 20 - Frame WeldingThe following instructions pertain to Work Center 20. (Setup hours = .15, Labor Hours = 1.75, Machine Hours = 2, Lot Sizing = 1) 
  <step>Assemble all frame components following blueprint 
  <blueprint>1299</blueprint> . </step>
  <step>Weld all frame components together as shown in illustration 
  <diag>3</diag> </step>
  <step>Inspect all weld joints per Adventure Works Cycles Inspection Specification <specs>INFS-208</specs> . </step>
  </Location>
<Location LaborHours="1" LotSize="1" LocationID="30">
  Work Center 30 - Debur and PolishThe following instructions pertain to Work Center 30. (Setup hours = 0, Labor Hours = 1, Machine Hours = 0, Lot Sizing = 1) 
  <step>Using the <tool>standard debur tool</tool> , remove all excess material from weld areas. </step>
  <step>Using <material>Acme Polish Cream</material> , polish all weld areas. </step>
  </Location>
<Location LaborHours="0.5" LotSize="20" MachineHours="0.65" LocationID="45">
  Work Center 45 - Specialized PaintThe following instructions pertain to Work Center 45. (Setup hours = 0, Labor Hours = .5, Machine Hours = .65, Lot Sizing = 20) 
  <step>Attach <material>a maximum of 20 frames</material> 
  to <tool>paint harness</tool> ensuring frames are not touching. 
  </step>
  <step>Mix <material>primer PA-529S</material>. Test spray pattern on sample area and correct flow and pattern as required per engineering spec 
  <specs>AWC-501</specs>. </step>
  <step>Apply thin coat of primer to all surfaces.</step> 
  <step>After 30 minutes, touch test for dryness. If dry to touch, lightly sand all surfaces. Remove all surface debris with compressed air.</step> 
  <step>Mix <material>paint</material> per manufacturer instructions. </step>
  <step>Test spray pattern on sample area and correct flow and pattern as required per engineering spec <specs>AWC-509</specs>.</step>
  <step>Apply thin coat of paint to all surfaces.</step> 
  <step>After 60 minutes, touch test for dryness. If dry to touch, reapply second coat.</step> 
  <step> Allow paint to cure for 24 hours and inspect per <specs>AWC-5015</specs> . </step>
  </Location>
<Location LaborHours="3" LotSize="1" SetupHours="0.25" LocationID="50">
  Work Center 50 - SubAssembly The following instructions pertain to Work Center 50. (Setup hours = .25, Labor Hours = 3, Machine Hours = 0, Lot Sizing = 1) 
  <step>Add Seat Assembly.</step> 
  <step>Add Brake assembly.</step> 
  <step>Add Wheel Assembly.</step> 
  <step>Inspect Front Derailleur.</step> 
  <step>Inspect Rear Derailleur.</step> 
  </Location>
<Location LaborHours="4" LotSize="1" LocationID="60">
  Work Center 60 - Final Assembly The following instructions pertain to Work Center 60. (Setup hours = 0, Labor Hours = 4, Machine Hours = 0, Lot Sizing = 1) 
<step>Perform final inspection per engineering specification 
  <specs>AWC-915</specs>. </step>
  <step>Complete all required certification forms.</step> 
  <step>Move to shipping.</step> 
  </Location>
  </root>

Daha fazla XML bulmak için aşağıdaki sorguyu çalıştırın:

SELECT Instructions
FROM   Production.ProductModel

See Also

Concepts