共用方式為


Add DirectAccess to an Existing Remote Access (VPN) Deployment

 

Applies To: Windows Server 2012 R2, Windows Server 2012

Note: Windows Server 2012 combines DirectAccess and Routing and Remote Access Service (RRAS) into a single Remote Access role. 

This topic provides an introduction to the Remote Access Enable DirectAccess Wizard, which is used to set up a single Remote Access server with recommended settings after you have already set up a virtual private network (VPN).

Deployment documentation set for Windows Server 2012 Remote Access (DirectAccess)

Following is a list of topics that you can use to deploy Remote Access through three main paths:

  • Basic

  • Advanced

  • Enterprise

Topics related to managing and migrating Remote Access that are available for this release are also listed.

Before you begin your deployment, see the following list of unsupported configurations, known issues, and prerequisites:

Basic Remote Access deployment

Advanced Remote Access deployment

Remote Access deployment in an enterprise

Manage Remote Access

Migrate Remote Access

Scenario description

In this scenario, a single computer running Windows Server 2012 is configured as a Remote Access server with recommended settings after you have already installed and configured VPN. If you want to configure Remote Access with enterprise features such as a load-balanced cluster, multisite deployment, or two-factor client authentication, complete the scenario described in this topic to set up a single server, and then set up the enterprise scenario as described in Deploy Remote Access in an Enterprise.

In this scenario

To set up a single Remote Access server, a number of planning and deployment steps are required.

Planning steps

Planning is divided into two phases:

  1. Plan the Remote Access infrastructure

    In this phase, you describe the planning that is required to set up the network infrastructure before you begin the Remote Access deployment. It includes planning for the network and server topology, certificates, Domain Name System (DNS), Active Directory and Group Policy Object (GPO) configuration, and the DirectAccess network location server.

  2. Plan the Remote Access deployment

    In this phase, you describe the planning steps that are required to prepare for the Remote Access deployment. It includes planning for Remote Access client computers, server and client authentication requirements, and infrastructure servers.

Deployment steps

Deployment is divided into three phases:

  1. Configure the Remote Access infrastructure

    In this phase, you configure the network and routing, firewall settings (if required), certificates, DNS servers, Active Directory and GPO settings, and the DirectAccess network location server.

  2. Configure Remote Access server settings

    In this phase, you configure the Remote Access client computers, the Remote Access server, and the infrastructure servers.

  3. Verify the deployment

    In this phase, you verify that the deployment is working as required.

Practical applications

Deploying a single Remote Access server provides the following:

  • Ease of access

    Managed client computers running Windows 8 and Windows 7 can be configured as DirectAccess client computers. These clients can access internal network resources through DirectAccess any time they are located on the Internet, without the need to sign in to a VPN connection. Client computers that are not running one of these operating systems can connect to the internal network through a VPN. DirectAccess and VPN are managed in the same console and with the same set of wizards.

  • Ease of management

    DirectAccess client computers that have access to the Internet can be remotely managed by remote access administrators by using DirectAccess, even when the client computers are not located on the internal corporate network. Client computers that do not meet corporate requirements can be remediated automatically by management servers.

Roles and features required for this scenario

The following table lists the roles and features that are required for this scenario:

Role/feature

How it supports this scenario

Remote Access role

The role is installed and uninstalled by using the Server Manager console or Windows PowerShell. This role encompasses DirectAccess, which was previously a feature in Windows Server 2008 R2, and Routing and Remote Access Services, which was previously a role service under the Network Policy and Access Services (NPAS) server role. The Remote Access role consists of two components:

  1. DirectAccess and Routing and Remote Access Services (RRAS) VPN: Managed in the Remote Access Management console.

  2. RRAS Routing: Managed in the Routing and Remote Access console.

The Remote Access Server role is dependent on the following server features:

  • Internet Information Services (IIS) Web Server:Required to configure the network location server on the Remote Access server, and the default web probe.

  • Windows Internal Database: Used for local accounting on the Remote Access server.

Remote Access Management Tools feature

This feature is installed as follows:

  • By default on a Remote Access server when the Remote Access role is installed. Supports the Remote Management console user interface and the Windows PowerShell cmdlets.

  • Optionally installed on a server not running the Remote Access server role. In this case, it is used for remote management of a Remote Access computer running DirectAccess and VPN.

The Remote Access Management Tools feature consists of the following:

  • Remote Access GUI

  • Remote Access module for Windows PowerShell

Dependencies include:

  • Group Policy Management Console

  • RAS Connection Manager Administration Kit (CMAK)

  • Windows PowerShell 3.0

  • Graphical Management Tools and Infrastructure

Hardware requirements

Hardware requirements for this scenario include the following:

Server requirements 

  • A computer that meets the hardware requirements for Windows Server 2012.

  • The server must have at least one network adapter installed, enabled, and joined to the internal network. When two adapters are used, there should be one adapter connected to the internal corporate network, and one connected to the external network (Internet).

  • If Teredo is required as an IPv4 to IPv6 transition protocol, the external adapter of the server requires two consecutive public IPv4 addresses. The Enable DirectAccess Wizard does not enable Teredo, even if two consecutive IP addresses are present. To enable Teredo, see Deploy a Single DirectAccess Server with Advanced Settings. If a single IP address is available, only IP-HTTPS can be used as the transition protocol.

  • At least one domain controller. The Remote Access server and DirectAccess clients must be domain members.

  • The Enable DirectAccess Wizard requires certificates for IP-HTTPS and the network location server. If the SSTP VPN is already using a certificate, it is reused for IP-HTTPS. If the SSTP VPN is not configured, you can configure a certificate for IP-HTTPS or use an automatically created self-signed certificate. For the network location server, you can configure a certificate or use an automatically created self-signed certificate.

Client requirements

  • A client computer must be running Windows 8 or Windows 7.

    Note

    Only the following operating systems can be used as DirectAccess clients: Windows Server 2012, Windows Server 2008 R2, Windows 8 Enterprise, Windows 7 Enterprise, and Windows 7 Ultimate.

Infrastructure and management server requirements

  • During the remote management of DirectAccess client computers, clients initiate communication with management servers, such as domain controllers, System Center configuration servers, and Health Registration Authority (HRA) servers for services that include Windows and antivirus updates and Network Access Protection (NAP) client compliance. The required servers should be deployed before you begin the Remote Access deployment.

  • If remote access requires client NAP compliance, the Network Policy Server (NPS) and the HRA should be deployed before you begin the Remote Access deployment.

  • A DNS server running Windows Server 2012, Windows Server 2008 R2, or Windows Server 2008 with SP2 is required.

Software requirements

Software requirements for this scenario include the following:

Server requirements

  • The Remote Access server must be a domain member. The server can be deployed at the edge of the internal network, or behind an edge firewall or other device.

  • If the Remote Access server is located behind an edge firewall or network address translation (NAT) device, the device must be configured to allow traffic to and from the Remote Access server.

  • The person who deploys remote access on the server requires local administrator permissions on the server, and domain user permissions. In addition, the administrator requires permissions for the GPOs that are used in DirectAccess deployment. To take advantage of the features that restrict a DirectAccess deployment to mobile computers only, permissions to create a WMI filter on the domain controller are required.

Remote access client requirements

  • DirectAccess clients must be domain members. Domains that contain clients can belong to the same forest as the Remote Access server, or they can have a two-way trust with the Remote Access server forest or domain.

  • An Active Directory security group is required to contain the computers that will be configured as DirectAccess clients. If a security group is not specified when you configure DirectAccess client settings, by default, the client GPO is applied on all laptop computers (that are DirectAccess capable) in the Domain Computers security group. Only the following operating systems can be used as DirectAccess clients: Windows Server 2012, Windows Server 2008 R2, Windows 8 Enterprise, Windows 7 Enterprise, and Windows 7 Ultimate.

    Note

    We recommend that you create a security group for each domain that contains computers that will be configured as DirectAccess clients.

See also

The following table provides links to additional resources.

Content type

References

Remote Access on TechNet

Remote Access TechCenter

Product evaluation

Demonstrate DirectAccess in a cluster with NLB

Demonstrate a DirectAccess multisite deployment

Demonstrate a DirectAccess multisite deployment

Deployment

Remote Access

Tools and settings

Remote Access PowerShell cmdlets 

Community resources

Related technologies

How IPv6 works