共用方式為


Managing the New Wireless Network (IEEE 802.11) Policies Settings

 

Applies To: Windows Server 2012

Wireless network settings in the Wireless Network (IEEE 802.11) Policies Group Policy extension include global wireless settings, the list of preferred networks, Wired Equivalent Privacy (WEP) and Wi-Fi Protected Access (WPA) settings, and Institute of Electrical and Electronics Engineers (IEEE) 802.1X settings.. You can use the New Wireless Network Policy to configure wireless settings on computers running Windows® 8, Windows® 7, and Windows Vista®.

There are two main sections in this topic:

  1. Configuring Wireless Network (IEEE 802.11) Policies, provides prescriptive guidance for configuring 802.1X authenticated wireless access based on one of the authentication methods you have selected when configuring this policy.

  2. Wireless Network (IEEE 802.11) Policies settings, provides configuration details about the individual settings in this policy.

Configuring Wireless Network (IEEE 802.11) Policies

This section provides step-by-step details to configure Wireless Network (IEEE 802.11) Policies extension of Group Policy for 802.1X authenticated wireless network access.

In this section:

  1. Configure a wireless connection profile for PEAP-MS-CHAP v2

  2. Configure a wireless connection profile for PEAP-TLS

  3. Configure a wireless connection profile for EAP-TLS

Configure a wireless connection profile for PEAP-MS-CHAP v2

This procedure provides the steps that are required to configure a wireless connection profile for Protected Extensible Authentication Protocol–Microsoft-Challenge Handshake Authentication Protocol (PEAP-MS-CHAP v2) for authentication by using secure passwords.

Membership in Domain Admins, or equivalent, is the minimum requirement to complete this procedure.

To configure a Windows Vista wireless connection profile for PEAP-MS-CHAP v2

  1. If you have not already done so, open the Windows Vista Wireless Network (IEEE 802.11) Policies properties page.

  2. In Windows Vista Wireless Network (IEEE 802.11) Policies Properties, on the General tab, select Use Windows to configure wireless network settings for clients to specify that WLAN AutoConfig is used to configure wireless network adapter settings.

  3. In Windows Vista Wireless Network (IEEE 802.11) Policies Properties, on the General tab, do one of the following:

    • To add and configure a new profile, click Add, and then select Infrastructure.

    • To edit an existing profile, select the profile that you want to modify, and then click Edit.

  4. On the Connection tab, in Profile Name, if you are adding a new profile, type a name for the profile. If you are editing a profile that is already added, use the existing profile name, or modify the name as needed.

  5. In Network Name(s) (SSID), type the service set identifier (SSID) that corresponds to the SSID configured on your wireless APs, and then click Add.

    If your deployment uses multiple SSIDs and each wireless AP uses the same wireless security settings, repeat this step to add the SSID for each wireless AP to which you want this profile to apply.

    If your deployment uses multiple SSIDs and the security settings for each SSID do not match, configure a separate profile for each group of SSIDs that use the same security settings. For example, if you have one group of wireless APs configured to use WPA2-Enterprise and AES, and another group of wireless APs to use WPA-Enterprise and TKIP, configure a profile for each group of wireless APs.

  6. If NEWSSID is present, select it, and then click Remove.

  7. If you deployed wireless access points that are configured to suppress the broadcast beacon, select Connect even if the network is not broadcasting.

    Note

    Enabling this option can create a security risk because wireless clients will probe for and try to connect to any wireless network. By default, this setting is not enabled.

  8. Click the Security tab, click Advanced, and then configure the following:

    1. To configure advanced 802.1X settings, in IEEE 802.1X, select Enforce advanced 802.1X settings.

      When the advanced 802.1X settings are enforced, the default values for Max Eapol-Start Msgs, Held Period, Start Period, and Auth Period are sufficient for most wireless deployments.

    2. To enable Single Sign On, select Enable Single Sign On for this network.

    3. The remaining default values in Single Sign On are sufficient for typical wireless deployments.

    4. In Fast Roaming, if your wireless AP is configured for pre-authentication, select This network uses pre-authentication.

  9. Click OK to return to the Security tab. In Select the security methods for this network, in Authentication, if it is supported by your wireless AP and wireless client network adapters, select WPA2-Enterprise. Otherwise, select WPA-Enterprise.

  10. In Encryption, select AES, if it is supported by your wireless AP and wireless client network adapters. Otherwise, select TKIP.

    Note

    The settings for both Authentication and Encryption must match the settings configured on your wireless AP. On the Security tab, the default settings for Authentication Mode, Max Authentication Failures, and Cache user information for subsequent connections to this network are sufficient for typical wireless deployments.

  11. In Select a network authentication method, select Protected EAP (PEAP), and then click Properties. The Protected EAP Properties page opens.

  12. In Protected EAP Properties, verify that Validate server certificate is selected.

  13. In Trusted Root Certification Authorities, select the trusted root certification authority (CA) that issued the server certificate to your computer running Network Policy Server (NPS).

    Note

    This setting limits the root CAs that clients trust to the selected CAs. If no trusted root CAs are selected, clients will trust all root CAs listed in their trusted root certification authority store.

  14. Select Do not prompt user to authorize new servers or trusted certification authorities. Selecting this setting provides an enhanced user experience and better security.

  15. In the Select Authentication Method list, select Secured password (EAP-MS-CHAP v2).

  16. To enable PEAP Fast Reconnect, select Enable Fast Reconnect.

  17. If Network Access Protection (NAP) is configured on your network, select Enable Quarantine checks. Otherwise, clear this check box.

  18. Click Configure. In the EAP MSCHAPv2 Properties dialog box, verify Automatically use my Windows logon name and password (and domain if any) is selected, click OK, and then click OK to close Protected EAP Properties.

  19. Click OK to close the Security tab, and then click OK again to close the Windows Vista Wireless Network Policy.

Configure a wireless connection profile for PEAP-TLS

This procedure provides the steps that are required to configure a Protected Extensible Authentication Protocol–Transport Level Security (PEAP-TLS) wireless connection profile for authentication using smart cards or other certificates.

Membership in Domain Admins, or equivalent, is the minimum requirement to complete this procedure.

To configure a Windows Vista PEAP-TLS wireless connection profile

  1. If you have not already done so, open the Windows Vista Wireless Network (IEEE 802.11) Policies properties page.

  2. In Windows Vista Wireless Network (IEEE 802.11) Policies Properties, on the General tab, select Use Windows to configure wireless network settings for clients to specify that WLAN AutoConfig is used to configure wireless network adapter settings.

  3. In Windows Vista Wireless Network (IEEE 802.11) Policies Properties, on the General tab, do one of the following:

    • To add and configure a new profile, click Add, and then select Infrastructure.

    • To edit an existing profile, select the profile that you want to modify, and then click Edit.

  4. On the Connection tab, in Profile Name, if you are adding a new profile, type a name for the profile. If you are editing a profile that is already added, use the existing profile name, or modify the name as needed.

  5. In Network Name(s) (SSID), type the service set identifier (SSID) that corresponds to the SSID configured on your wireless APs, and then click Add.

    If your deployment uses multiple SSIDs and each wireless AP uses the same wireless security settings, repeat this step to add the SSID for each wireless AP to which you want this profile to apply.

    If your deployment uses multiple SSIDs and the security settings for each SSID do not match, configure a separate profile for each group of SSIDs that use the same security settings. For example, if you have one group of wireless APs configured to use WPA2-Enterprise and AES, and another group of wireless APs to use WPA-Enterprise and TKIP, configure a profile for each group of wireless APs.

  6. If NEWSSID is present, select it, and then click Remove.

  7. If you deployed wireless access points that are configured to suppress the broadcast beacon, select Connect even if the network is not broadcasting.

    Note

    Enabling this option can create a security risk because wireless clients will probe for and try to connect to any wireless network. By default, this setting is not enabled.

  8. Click the Security tab, click Advanced, and then configure the following:

    1. To configure advanced 802.1X settings, in IEEE 802.1X, select Enforce advanced 802.1X settings.

      When the advanced 802.1X settings are enforced, the default values for Max Eapol-Start Msgs, Held Period, Start Period, and Auth Period are sufficient for most wireless deployments.

    2. To enable Single Sign On, select Enable Single Sign On for this network.

    3. The remaining default values in Single Sign On are sufficient for typical wireless deployments.

    4. In Fast Roaming, if your wireless AP is configured for pre-authentication, select This network uses pre-authentication.

  9. Click OK to return to the Security tab. In Select the security methods for this network, in Authentication, select WPA2-Enterprise if it is supported by your wireless AP and wireless client network adapters. Otherwise, select WPA-Enterprise.

  10. In Encryption, if it is supported by your wireless AP and wireless client network adapters, select AES. Otherwise, select TKIP.

    Note

    The settings for both Authentication and Encryption must match the settings configured on your wireless AP. On the Security tab, the default settings for Authentication Mode, Max Authentication Failures, and Cache user information for subsequent connections to this network are sufficient for typical wireless deployments.

  11. In Select a network authentication method, select Protected EAP (PEAP), and then click Properties. The Protected EAP Properties page opens.

  12. In Protected EAP Properties, verify that Validate server certificate is selected.

  13. In Trusted Root Certification Authorities, select the trusted root certification authority (CA) that issued server certificates to your computers running Network Policy Server (NPS).

    Note

    This setting limits the root CAs that clients trust to the selected CAs. If no trusted root CAs are selected, clients will trust all root CAs listed in their trusted root certification authority store.

  14. Select Do not prompt user to authorize new servers or trusted certification authorities. Selecting this setting provides an enhanced user experience and better security.

  15. In the Select Authentication Method list, select Smart Card or other certificate.

  16. To enable PEAP Fast Reconnect, select Enable Fast Reconnect.

  17. If Network Access Protection (NAP) is configured on your network, select Enable Quarantine checks. Otherwise, clear this check box.

  18. Click Configure. In the Smart Card or other Certificate Properties dialog box, in When connecting, specify one of the following.

    • For deployments that use smart cards, select Use my smart card.

    • For other certificate deployments, select Use a certificate on this computer.

  19. Select Validate server certificate.

  20. To specify which NPS servers your client computers can use for authentication and authorization, select connect to these servers, and then for each NPS server, type the name of each server, exactly as it appears in the Subject filed of each NPS server’s certificate, separated by a semicolon.

  21. In Trusted Root Certification Authorities, select the CA that issued certificates to your NPS servers.

  22. Click OK two times, to close the Protected EAP properties, returning you to the Security tab.

  23. Click OK to close the Security tab, and then click OK again to close the Windows Vista Wireless Network Policy.

Configure a wireless connection profile for EAP-TLS

This procedure provides the steps that are required to configure an Extensible Authentication Protocol–Transport Level Security (EAP-TLS) wireless profile for authentication by using secure passwords.

Membership in Domain Admins, or equivalent, is the minimum requirement to complete this procedure.

To configure an EAP-TLS wireless profile

  1. In Windows Vista Wireless Network (IEEE 802.11) Policies Properties, on the General tab, click Add, and then select Infrastructure.

    Note

    For more information about the settings on any tab, press F1 while you are viewing that tab.

  2. On the Connection tab, do the following:

    1. In Profile Name, type a name for the EAP-based profile.

    2. In Network Name(s) (SSID), type the service set identifier (SSID) that corresponds to the SSID configured on your wireless APs, and then click Add.

    3. If present, select NEWSSID, and then click Remove.

    4. If your wireless access point is configured to suppress its broadcast beacon, select Connect even if the network is not broadcasting.

      Note

      Enabling this option can create a security risk because wireless clients will probe for and try to connect to any wireless network. By default, this setting is not enabled.

  3. Select the Security tab, click Advanced, and then configure the following:

    1. To configure advanced 802.1X settings, in IEEE 802.1X, select Enforce advanced 802.1X settings.

      Note

      When the advanced 802.1X settings are enforced, the default values for Max Eapol-Start Msgs, Held period, Start Period, and Auth Period are sufficient for most wireless deployments.

    2. In Single Sign On, select Enable Single Sign On for this network.

      Note

      The remaining default values in Single Sign On are sufficient for most wireless deployments.

    3. In Fast Roaming, if your wireless AP is configured for pre-authentication, select This network uses pre-authentication.

  4. Click OK to return to the Security tab, and then configure the following:

    1. In Select the security methods for this network, for Authentication, if it is supported by your wireless AP and wireless client network adapters, select WPA2-Enterprise. Otherwise, select WPA-Enterprise.

    2. In Encryption, if it is supported by your wireless AP and wireless client network adapters, select AES (preferred). Otherwise, select TKIP.

      Note

      The settings for both Authentication and Encryption must match the settings configured on your wireless AP. On the Security tab, the default settings for Authentication Mode, Max Authentication Failures, and Cache user information for subsequent connections to this network are sufficient for most wireless deployments.

  5. In Select a network authentication method, select Smart Card or other certificate (EAP-TLS). On the Security tab, click Properties, and then configure the following:

    1. In When connecting, verify that Use a certificate on this computer and Use simple certificate selection are selected.

    2. Verify that Validate server certificate is selected.

      In Trusted Root Certification Authorities, select the trusted root certification authority (CA) that issued the server certificate to your computers running Network Policy Server (NPS).

      Note

      This setting limits the trusted root CAs that clients trust to the selected values. If no trusted root CAs are selected, clients will trust all trusted root CAs listed in their trusted root certification authority store.

  6. Click OK to close Smart Card or other Certificate Properties, and then click OK again to close the EAP Profile.

Wireless Network (IEEE 802.11) Policies settings

This section provides configuration setting details about the New Wireless Network Policy. You can use the New Wireless Network Policy to configure wireless settings on computers running Windows® 8, Windows® 7, and Windows Vista®.

Wireless Policies for computers running Windows Vista and subsequent releases of Windows

In this section:

  1. General - settings

  2. Import and Export Wireless Network Profiles

  3. Connection - settings

  4. New Permissions Entry - settings

  5. Security – configuration items

    1. Select the security methods for this network - settings

    2. Select a network authentication method - settings

      Note

      Information about the network authentication methods is provided in the topic, Advanced Security Settings for Wired and Wireless Network Policies. Clicking this link will open a new Web page. A link is provided in the Additional Resources section of that topic to return you to this page.

      Note

      Information about the Advanced Security settings is provided in the topic, Advanced Security Settings for Wired and Wireless Network Policies. Clicking this link will open a new Web page. A link is provided in the Additional Resources section of that topic to return you to this page.

  6. Additional resources

General - settings

You can use the General tab to create and manage wireless network profiles and to define a list of preferred wireless networks, which prioritizes the order in which your domain-member clients attempt to connect. You can also specify whether the WLAN AutoConfig Service is used to configure 802.11 wireless adapters to connect to wireless networks.

Item

Details

Vista Policy Name

Provides a location for you to type a friendly name for the Wireless Network Policy.

Note

When you name the Wireless Network (IEEE 802.11) Policy, the name you specify is displayed as the title of its properties page, and under Name in the details pane in the Group Policy Management Console (GPMC) for that policy.

Description

Provides a location for you to type a description for the Wireless Policy.

Note

The description you type is displayed under Description in the details pane of the Group Policy Management Console (GPMC) for that policy.

Use Windows WLAN Auto Config service for clients

Specifies that the WLAN AutoConfig Service is used to configure and connect clients running Windows Vista® to the wireless network.

Default = enabled

Connect to available networks in the order of profiles listed below

Click the desired profile, and then use the Move Up and Move down buttons to specify the preferred order for clients to attempt connections.

Note

Profiles for ad-hoc networks cannot be prioritized higher than infrastructure profiles.

Add

Allows you to add a wireless network profile and specify the profile properties.

When you click Add, you will be presented with two options:

Ad-hoc. Specifies a computer-to-computer network. Access points are not used.

Infrastructure. Specifies a network that uses one or more wireless access points.

Edit

Select a network under Profile name and then click Edit to modify the properties of the wireless network profile.

Remove

Select a network under Profile name and then click Remove to delete the wireless network profile.

Import

Allows you to incorporate an existing wireless network profile, from a location you specify, into the list of available networks.

Export

Allows you to save a configured profile as an Extensible Markup Langage (XML) file.

Import and Export Wireless Network Profiles

Profile import and export are managed by using the following two interfaces. You can use Import a Profile to add a wireless network profile, from a location you specify, into the list of available wireless networks. You can use Save Export Profile to export any profile listed under Connect to available networks in the order of profiles listed below on the General tab, and save it to a location you specify.

Open for import a profile (Import Profiles)

Item

Details

Save in

Specifies the location to save a profile.

Name

Lists saved wireless profiles.

File name

Provides a location for you to type a name for the profile.

Save as type

Specifies the file type used to save the profile.

Save export profile as (Export Profiles)

Item

Details

Look in

Specifies the location of a saved profile.

Name

Lists saved profiles.

Select the profile you want to export, and then click Open.

File name

Provides a location for you to type a new name or modify the existing profile name.

Files of type

Specifies the file type for files that are displayed under Name.

Connection - settings

The Connection tab for the Wireless Network (IEEE 802.11) Policy allows you to create wireless network profiles and specify the name of each wireless network to which domain-member wireless clients can connect. Each network is saved as a profile. A profile is the collection of configuration settings for a wireless networks, saved as an Extensible Markup Language (XML) file.

Item

Details

Profile name

Specifies the friendly name for the wireless network profile.

Network Name (SSID)

Specifies the name of the wireless network. This must match the Service Set Identifier (SSID) configured on the wireless access points for this network.

Connect automatically when this network is in range

Specifies that Windows will automatically attempt to connect to the wireless network when the computer is within broadcast range of any wireless access points that are broadcasting the SSID.

Note

Windows attempts connections to wireless networks in the order they are listed in preferred networks.

Connect to a more preferred network if available

Specifies that clients will attempt to connect to wireless networks in the order specified under Connect to available networks in the order of profiles listed below on the General tab.

Connect even if the network is not broadcasting

Specifies that wireless clients will actively probe for wireless access points with the specified SSID, in case wireless access points are configured to suppress beacon broadcasts.

Network Permissions - settings

You can use Network Permissions to list and configure wireless networks that are not defined on the General tab in the Connect to available networks in the order of profiles listed below preferred list. You can use these settings to define additional wireless networks and specify whether you want to allow or deny connections by your domain-member wireless clients. Alternatively, you can block the additional wireless networks from being displayed to your domain-member wireless clients. These settings are specific to the wireless networks listed on the Network Permissions tab under Network Name (SSID).

Connections to the wireless networks that are listed under Network Name (SSID) on the Network Permissions tab are only possible if the permission is set to Allow. If the permission is set to Allow, your domain-member wireless clients first attempt to connect to a preferred network, before attempting to connect to non-preferred networks. However, domain members can actively launch a connection attempt to listed networks that have permissions set to Allow.

Item

Details

Network Name (SSID)

Lists wireless networks, for which you want to allow or deny permissions, but that are not defined on the General tab in Connect to available networks in the order of profiles listed below.

Default = disabled

Add

Opens the New Permission Entry dialog box, for adding a new wireless network to the permission list.

When you click Add, you will be presented with two options:

  • Ad-hoc. Specifies a computer-to-computer network. Access points are not used.

  • Infrastructure. Specifies a network that uses one or more wireless access points.

Remove

Deletes the selected wireless network from the permission list.

Prevent connections to ad-hoc networks

Specifies that domain-member wireless clients cannot form a new ad-hoc network or connect to any ad-hoc networks in the permission list.

Default = not enabled

Prevent connections to infrastructure networks

Specifies that domain-member wireless clients cannot connect to any infrastructure networks in the permission list.

Default = not enabled

Allow user to view denied networks

Specifies whether domain-member wireless clients can view wireless networks in the permission list that have permissions set to Deny.

Default = not enabled

Allow everyone to create all user profiles

Specifies that any user to which Wireless Network (IEEE 802.11) Policy applies can create all user wireless profiles on the computer. When this setting is not selected, only users in the Network Administrators group or Network Operators group can create all user wireless profiles on the computer.

All user profiles are wireless profiles that are used to connect to a specific wireless network and that can be started by any user with an account on the computer. Every user with an account on the computer is contained within the computer-wide access control list (ACL) named Everyone. Based on the Everyone ACL group, network administrators can use this setting to limit access to the controls that enable users to create all user profiles.

Default = enabled

New Permissions Entry - settings

You can use the Wireless Network (IEEE 802.11) Policy New Permission page to add new wireless networks to the permission list on the Networks Permissions tab. You can use New Permissions to specify, by Service Set Identifier (SSID), which wireless networks your wireless domain members are allowed to connect to, and which are denied.

Items

Details

Network Name (SSID)

Provides a location for you to type the name for the wireless network for which you want to set permissions.

Network Type

Specifies whether the network is infrastructure (uses a wireless access point) or ad-hoc (computer-to-computer).

Permission

Specifies whether to permit or deny connections to the selected network.

Security – configuration items

Security configuration items include all of the settings on the Security tab. These settings specify whether to perform 802.1X authentication for connecting clients, which network security authentication method to use, and which network authentication method to use.

Select the security methods for this network settings pertain to the authentication and security that the client uses to exchange data with the wireless access point.

Select a network authentication method settings pertain to the EAP method that is used for 802.1X authenticated network access.

Select the security methods for this network - settings

Item

Details

Authentication

Specifies the security authentication method to use when the wireless client associates with the wireless access point.

  • Open

  • Shared

  • WPA-Enterprise

  • WPA-Personal

  • WPA2-Enterprise

  • WPA2-Personal

  • Open with 802.1X

Note

Network Authentication Methods and advanced settings are only exposed by selecting WPA-Enterprise, WPA2-Enterprise, and Open with 802.1X for the network security authentication method.

Default = Defaults to the most secure setting supported by the wireless hardware and drivers.

Encryption

Specifies the security encryption to use for the selected network security authentication method.

If the Authentication is set to WPA-Enterprise, WPA-Personal, WPA2-Enterprise, or WPA2-Personal, the encryption options are AES or TKIP.

If Authentication is set to Open, Shared, or Open with 802.1X, then encryption options are either WEP or Disabled.

Select a network authentication method - settings

Item

Details

Select a network authentication method

Specifies the network authentication method that connecting wireless clients use.

  • Smart Card or other certificate

  • Protected EAP (PEAP)

Default = Protected EAP (PEAP)

Properties

Opens the properties page of the selected network authentication method.

For setting information for network authentication methods, see: Extensible Authentication Protocol (EAP) Settings for Network Access. Clicking this link will open a new Web page. A link is provided in the Additional Resources section of that topic to return you to this page.

Authentication Mode

Specifies how credentials are used for network authentication. The following options are available.

  • User re-authentication. An 802.1X-compliant device always uses security credentials based on the computer's current state. Authentication is performed by using the computer credentials when no users are logged on to the computer. When a user logs on to the computer, authentication is always performed by using the user credentials.

    This is the recommended setting.

  • Computer only. Authentication is always performed using only the computer credentials.

  • User authentication. Specifies that when users are not logged on to the computer, authentication is performed by using the computer credentials. After a user logs on to the computer, authentication is still based on the computer credentials. Authentication is performed by using the user credentials if the user travels to a new wireless access point.

  • Guest authentication. Allows connections to the network which are regulated by the restrictions and permissions set for the Guest user account.

Default = User re-authentication

Max Authentication Failures

Specifies the maximum number of failed authentication attempts that can occur with a specific set of credentials before notification is displayed to indicate that authentication has failed.

Default = 3

Clear credentials after logoff

Specifies that when the user logs off, the user credential data is removed from the registry. The result is that at the next user log on, they will be prompted for their credentials (such as user name and password).

Default = Not enabled

Authenticate as guest when user or computer information is unavailable

Specifies that client connection requests that cannot meet computer or user authentication requirements can connect to the network by using permissions configured for the Guest account.

Default = Not enabled

Advanced

Provides access to advanced security settings.

Note

Information about the Advanced Security settings is provided in the topic, Advanced Security Settings for Wired and Wireless Network Policies. Clicking this link will open a new Web page. A link is provided in the Additional Resources section of that topic to return you to this page.

Additional resources

For additional information about the Advanced Security settings, see Advanced Security Settings for Wired and Wireless Network Policies, in the Microsoft technical library on TechNet.

For additional information about network authentication methods, see Extensible Authentication Protocol (EAP) Settings for Network Access, in the Microsoft technical library on TechNet.