Test-IRMConfiguration
This cmdlet is available in on-premises Exchange and in the cloud-based service. Some parameters and settings may be exclusive to one environment or the other.
Use the Test-IRMConfiguration cmdlet to test Information Rights Management (IRM) configuration and functionality.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Test-IRMConfiguration
[[-Identity] <OrganizationIdParameter>]
-Sender <SmtpAddress>
[-Confirm]
[-DomainController <Fqdn>]
[-Recipient <SmtpAddress[]>]
[-RMSOnline]
[-WhatIf]
[<CommonParameters>]Description
The Test-IRMConfiguration cmdlet performs a series of steps to test IRM configuration and functionality, including availability of an Active Directory Rights Management Services (AD RMS) server, prelicensing and journal report decryption. In Exchange Online organizations, it checks connectivity to RMS Online and obtains and validates the organization's Trusted Publishing Domain (TPD).
You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
Test-IRMConfiguration -Sender adams@contoso.comThis example tests the IRM configuration in on-premises Exchange for messages sent from the sender adams@contoso.com.
Example 2
Test-IRMConfiguration -Sender chris@fabrikam.com -Recipient michell@fourthcoffee.comThis example tests the IRM configuration in the cloud-based service for messages sent from chris@fabrikam.com to michell@fourthcoffee.com.
Parameters
-Confirm
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
| Type: | SwitchParameter |
| Aliases: | cf |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online, Exchange Online Protection |
-DomainController
This parameter is available only in on-premises Exchange.
The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.
| Type: | Fqdn |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-Identity
This parameter is available only in on-premises Exchange.
This parameter is reserved for internal Microsoft use.
| Type: | OrganizationIdParameter |
| Position: | 1 |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | True |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-Recipient
The Recipient parameter specifies the email address of the recipient to test. You can specify multiple email addresses separated by commas.
This parameter is required in the cloud-based service.
In on-premises Exchange, if you don't use this parameter, the sender address that's specified by the Sender parameter is used for the value of this parameter.
| Type: | SmtpAddress[] |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online, Exchange Online Protection |
-RMSOnline
This parameter is available only in the cloud-based service.
The RMSOnline switch specifies whether to test connectivity from Exchange Online to RMS Online, obtain your Exchange Online organization's TPD, and test its validity. You don't need to specify a value with this switch.
| Type: | SwitchParameter |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online, Exchange Online Protection |
-Sender
The Sender parameter specifies the email address of the sender to test.
| Type: | SmtpAddress |
| Position: | Named |
| Default value: | None |
| Required: | True |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online, Exchange Online Protection |
-WhatIf
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
| Type: | SwitchParameter |
| Aliases: | wi |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online, Exchange Online Protection |
Inputs
Input types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.
Outputs
Output types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.