Freigeben über

Wait-Event

Modul:
Microsoft.PowerShell.Utility Module

Waits until a particular event is raised before continuing to run.

Syntax

Default (Standardwert) 

Wait-Event
    [[-SourceIdentifier] <String>]
    [-Timeout <Int32>]
    [<CommonParameters>]

Beschreibung

The Wait-Event cmdlet suspends execution of a script or function until a particular event is raised. Execution resumes when the event is detected. To cancel the wait, press CTRL+C.

This feature provides an alternative to polling for an event. It also allows you to determine the response to an event in two different ways:

  • using the Action parameter of the event subscription
  • waiting for an event to return and then respond with an action

Beispiele

Example 1: Wait for the next event

This example waits for the next event that is raised.

Wait-Event

Example 2: Wait for an event with a specified source identifier

This example waits for the next event that is raised and that has a source identifier of ProcessStarted.

Wait-Event -SourceIdentifier "ProcessStarted"

Example 3: Wait for a timer elapsed event

This example uses the Wait-Event cmdlet to wait for a timer event on a timer that is set for 2000 milliseconds.

$Timer = New-Object Timers.Timer
$objectEventArgs = @{
    InputObject = $Timer
    EventName = 'Elapsed'
    SourceIdentifier = 'Timer.Elapsed'
}
Register-ObjectEvent @objectEventArgs
$Timer.Interval = 2000
$Timer.Autoreset = $false
$Timer.Enabled = $true
Wait-Event Timer.Elapsed

ComputerName     :
RunspaceId       : bb560b14-ff43-48d4-b801-5adc31bbc6fb
EventIdentifier  : 1
Sender           : System.Timers.Timer
SourceEventArgs  : System.Timers.ElapsedEventArgs
SourceArgs       : {System.Timers.Timer, System.Timers.ElapsedEventArgs}
SourceIdentifier : Timer.Elapsed
TimeGenerated    : 4/23/2020 2:30:37 PM
MessageData      :

Example 4: Wait for an event after a specified timeout

This example waits up to 90 seconds for the next event that is raised and that has a source identifier of ProcessStarted. If the specified time expires, the wait ends.

Wait-Event -SourceIdentifier "ProcessStarted" -Timeout 90

Parameter

-SourceIdentifier

Specifies the source identifier that this cmdlet waits for events. By default, Wait-Event waits for any event.

Parametereigenschaften

Typ:String
Standardwert:None
Unterstützt Platzhalter:False
Nicht anzeigen:False

Parametersätze

(All)
Position:0
Obligatorisch.:False
Wert aus Pipeline:False
Wert aus Pipeline nach dem Eigenschaftsnamen:True
Wert aus verbleibenden Argumenten:False

-Timeout

Specifies the maximum time, in seconds, that Wait-Event waits for the event to occur. The default, -1, waits indefinitely. The timing starts when you submit the Wait-Event command.

If the specified time is exceeded, the wait ends and the command prompt returns, even if the event has not been raised. No error message is displayed.

Parametereigenschaften

Typ:Int32
Standardwert:-1
Unterstützt Platzhalter:False
Nicht anzeigen:False
Aliase:TimeoutSec

Parametersätze

(All)
Position:Named
Obligatorisch.:False
Wert aus Pipeline:False
Wert aus Pipeline nach dem Eigenschaftsnamen:False
Wert aus verbleibenden Argumenten:False

CommonParameters

This cmdlet supports the common parameters: -Debug, -ErrorAction, -ErrorVariable, -InformationAction, -InformationVariable, -OutBuffer, -OutVariable, -PipelineVariable, -ProgressAction, -Verbose, -WarningAction, and -WarningVariable. For more information, see about_CommonParameters.

Eingaben

String

Ausgaben

PSEventArgs

Hinweise

Events, event subscriptions, and the event queue exist only in the current session. If you close the current session, the event queue is discarded and the event subscription is canceled.