Επεξεργασία

Κοινή χρήση μέσω


Train PyTorch Model

This article describes how to use the Train PyTorch Model component in Azure Machine Learning designer to train PyTorch models like DenseNet. Training takes place after you define a model and set its parameters, and requires labeled data.

Currently, Train PyTorch Model component supports both single node and distributed training.

How to use Train PyTorch Model

  1. Add DenseNet component or ResNet to your pipeline draft in the designer.

  2. Add the Train PyTorch Model component to the pipeline. You can find this component under the Model Training category. Expand Train, and then drag the Train PyTorch Model component into your pipeline.

    Note

    Train PyTorch Model component is better run on GPU type compute for large dataset, otherwise your pipeline will fail. You can select compute for specific component in the right pane of the component by setting Use other compute target.

  3. On the left input, attach an untrained model. Attach the training dataset and validation dataset to the middle and right-hand input of Train PyTorch Model.

    For untrained model, it must be a PyTorch model like DenseNet; otherwise, a 'InvalidModelDirectoryError' will be thrown.

    For dataset, the training dataset must be a labeled image directory. Refer to Convert to Image Directory for how to get a labeled image directory. If not labeled, a 'NotLabeledDatasetError' will be thrown.

    The training dataset and validation dataset have the same label categories, otherwise a InvalidDatasetError will be thrown.

  4. For Epochs, specify how many epochs you'd like to train. The whole dataset will be iterated in every epoch, by default 5.

  5. For Batch size, specify how many instances to train in a batch, by default 16.

  6. For Warmup step number, specify how many epochs you'd like to warm up the training, in case initial learning rate is slightly too large to start converging, by default 0.

  7. For Learning rate, specify a value for the learning rate, and the default value is 0.001. Learning rate controls the size of the step that is used in optimizer like sgd each time the model is tested and corrected.

    By setting the rate smaller, you test the model more often, with the risk that you might get stuck in a local plateau. By setting the rate larger, you can converge faster, with the risk of overshooting the true minima.

    Note

    If train loss becomes nan during training, which may be caused by too large learning rate, decreasing learning rate may help. In distributed training, to keep gradient descent stable, the actual learning rate is calculated by lr * torch.distributed.get_world_size() because batch size of the process group is world size times that of single process. Polynomial learning rate decay is applied and can help result in a better performing model.

  8. For Random seed, optionally type an integer value to use as the seed. Using a seed is recommended if you want to ensure reproducibility of the experiment across jobs.

  9. For Patience, specify how many epochs to early stop training if validation loss does not decrease consecutively. by default 3.

  10. For Print frequency, specify training log print frequency over iterations in each epoch, by default 10.

  11. Submit the pipeline. If your dataset has larger size, it will take a while and GPU compute are recommended.

Distributed training

In distributed training the workload to train a model is split up and shared among multiple mini processors, called worker nodes. These worker nodes work in parallel to speed up model training. Currently the designer support distributed training for Train PyTorch Model component.

Training time

Distributed training makes it possible to train on a large dataset like ImageNet (1000 classes, 1.2 million images) in just several hours by Train PyTorch Model. The following table shows training time and performance during training 50 epochs of Resnet50 on ImageNet from scratch based on different devices.

Devices Training Time Training Throughput Top-1 Validation Accuracy Top-5 Validation Accuracy
16 V100 GPUs 6h22min ~3200 Images/Sec 68.83% 88.84%
8 V100 GPUs 12h21min ~1670 Images/Sec 68.84% 88.74%

Click on this component 'Metrics' tab and see training metric graphs, such as 'Train images per second' and 'Top 1 accuracy'.

Screenshot showing training metrics

How to enable distributed training

To enable distributed training for Train PyTorch Model component, you can set in Job settings in the right pane of the component. Only AML Compute cluster is supported for distributed training.

Note

Multiple GPUs are required to activate distributed training because NCCL backend Train PyTorch Model component uses needs cuda.

  1. Select the component and open the right panel. Expand the Job settings section.

    Screenshot showing how to set distributed training in runsetting

  2. Make sure you have select AML compute for the compute target.

  3. In Resource layout section, you need to set the following values:

    • Node count : Number of nodes in the compute target used for training. It should be less than or equal to the Maximum number of nodes your compute cluster. By default it is 1, which means single node job.

    • Process count per node: Number of processes triggered per node. It should be less than or equal to the Processing Unit of your compute. By default it is 1, which means single process job.

    You can check the Maximum number of nodes and Processing Unit of your compute by clicking the compute name into the compute detail page.

    Screenshot showing how to check compute cluster

You can learn more about distributed training in Azure Machine Learning here.

Troubleshooting for distributed training

If you enable distributed training for this component, there will be driver logs for each process. 70_driver_log_0 is for master process. You can check driver logs for error details of each process under Outputs+logs tab in the right pane.

Screenshot showing driver log

If the component enabled distributed training fails without any 70_driver logs, you can check 70_mpi_log for error details.

The following example shows a common error, which is Process count per node is larger than Processing Unit of the compute.

Screenshot showing mpi log

You can refer to this article for more details about component troubleshooting.

Results

After pipeline job is completed, to use the model for scoring, connect the Train PyTorch Model to Score Image Model, to predict values for new input examples.

Technical notes

Expected inputs

Name Type Description
Untrained model UntrainedModelDirectory Untrained model, require PyTorch
Training dataset ImageDirectory Training dataset
Validation dataset ImageDirectory Validation dataset for evaluation every epoch

Component parameters

Name Range Type Default Description
Epochs >0 Integer 5 Select the column that contains the label or outcome column
Batch size >0 Integer 16 How many instances to train in a batch
Warmup step number >=0 Integer 0 How many epochs to warm up training
Learning rate >=double.Epsilon Float 0.1 The initial learning rate for the Stochastic Gradient Descent optimizer.
Random seed Any Integer 1 The seed for the random number generator used by the model.
Patience >0 Integer 3 How many epochs to early stop training
Print frequency >0 Integer 10 Training log print frequency over iterations in each epoch

Outputs

Name Type Description
Trained model ModelDirectory Trained model

Next steps

See the set of components available to Azure Machine Learning.