Muokkaa

Jaa


HPE ProLiant DL20 Gen10 Plus (4SFF)

This article describes the HPE ProLiant DL20 Gen10 Plus appliance for OT sensors in an enterprise deployment.

The HPE ProLiant DL20 Gen10 Plus is also available for the on-premises management console.

Appliance characteristic Details
Hardware profile E1800
Performance Max bandwidth: 1 Gbps
Max devices: 10,000
Up to 8x RJ45 monitoring ports or 6x SFP (OPT)
Physical specifications Mounting: 1U
Minimum dimensions (H x W x D) 1.70 x 17.11 x 15.05 in
Minimum dimensions (H x W x D) 4.32 x 43.46 x 38.22 cm
Status Supported, available pre-configured

The following image shows a sample of the HPE ProLiant DL20 front panel:

Photo of the HPE ProLiant DL20 front panel.

The following image shows a sample of the HPE ProLiant DL20 back panel:

Photo of the back panel of the HPE ProLiant DL20.

Specifications

Component Technical specifications
Chassis 1U rack server
Physical Characteristics HPE DL20 Gen10+ NHP 4SFF CTO Server
Processor Intel Xeon E-2334
3.4 GHz 4C 65 W
Chipset Intel C256
Memory 2x 16-GB Dual Rank x8 DDR4-3200
Storage 4x 1-TB SATA 6G Midline 7.2 K SFF (2.5 in) – RAID 10
Network controller On-board: 2x 1 Gb
External 1 x HPE Ethernet 1-Gb 4-port 366FLR Adapter
On-board iLO Port Card 1 Gb
Management HPE iLO Advanced
Device access Front: One USB 3.0 1 x USB iLO Service Port
Rear: Two USBs 3.0
Internal One USB 3.0
Power 2x Hot Plug Power Supply 290 W
Rack support HPE 1U Short Friction Rail Kit

DL20 Gen10 Plus (4SFF) - Bill of materials

Quantity PN Description
1 P44111-B21 HPE DL20 Gen10+ 4SFF CTO Server
1 P45252-B21 Intel Xeon E-2334 FIO CPU for HPE
4 P28610-B21 HPE 1-TB SATA 7.2K SFF BC HDD
2 P43019-B21 HPE 16 GB 1Rx8 PC4-3200AA-E Standard Kit
1 869079-B21 HPE Smart Array E208i-a SR G10 LH Ctrlr (RAID10)
1 P21106-B21 INT I350 1 GbE 4p BASE-T Adapter
1 P45948-B21 HPE DL20 Gen10+ RPS FIO Enable Kit
2 865408-B21 HPE 500 W FS Plat Hot Plug LH Power Supply Kit
1 775612-B21 HPE 1U Short Friction Rail Kit
1 512485-B21 HPE iLO Adv 1 Server License 1 year support
1 P46114-B21 HPE DL20 Gen10+ 2x8 LP FIO Riser Kit

Optional Storage Controllers

Multi-disk RAID arrays combine multiple physical drives into one logical drive for increased redundancy and performance. The optional modules below were tested in our lab for compatibility and sustained performance:

Quantity PN Description
1 869079-B21 HPE Smart Array E208i-a SR G10 LH Ctrlr (RAID10)
1 P26325-B21 Broadcom MegaRAID MR216i-a x16 Lanes without Cache NVMe/SAS 12G Controller (RAID5)

Note: This RAID controller occupies the PCIe expansion slot and doesn't allow expansion of networking port expansion

Optional port expansion

Optional modules for port expansion include:

Location Type Specifications
PCI Slot 1 (Low profile) DP F/O NIC P26262-B21 - Broadcom BCM57414 Ethernet 10/25Gb 2-port SFP28 Adapter for HPE
PCI Slot 1 (Low profile) DP F/O NIC P28787-B21 - Intel X710-DA2 Ethernet 10-Gb 2-port SFP+ Adapter for HPE
PCI Slot 2 (High profile) Quad Port Ethernet NIC P21106-B21 - Intel I350-T4 Ethernet 1-Gb 4-port BASE-T Adapter for HPE
PCI Slot 2 (High profile) DP F/O NIC P26262-B21 - Broadcom BCM57414 Ethernet 10/25 Gb 2-port SFP28 Adapter for HPE
PCI Slot 2 (High profile) DP F/O NIC P28787-B21 - Intel X710-DA2 Ethernet 10-Gb 2-port SFP+ Adapter for HPE
SFPs for Fiber Optic NICs MultiMode, Short Range 455883-B21 - HPE BLc 10G SFP+ SR Transceiver
SFPs for Fiber Optic NICs SingleMode, Long Range 455886-B21 - HPE BLc 10G SFP+ LR Transceiver

HPE ProLiant DL20 Gen10 Plus installation

This section describes how to install Defender for IoT software on the HPE ProLiant DL20 Gen10 Plus appliance.

Installation includes:

  • Enabling remote access and updating the default administrator password
  • Configuring iLO port on network port 1
  • Configuring BIOS and RAID10 settings
  • Installing Defender for IoT software

Note

Installation procedures are only relevant if you need to re-install software on a pre-configured device, or if you buy your own hardware and configure the appliance yourself.

Enable remote access and update the password

Use the following procedure to set up network options and update the default password.

To enable, and update the password:

  1. Connect a screen and a keyboard to the HPE appliance, turn on the appliance, and press F9.

    Screenshot that shows the HPE ProLiant window.

  2. Go to System Utilities > System Configuration > iLO 5 Configuration Utility > Network Options.

    Screenshot that shows the System Configuration window.

    1. Select Shared Network Port-LOM from the Network Interface Adapter field.

    2. Set Enable DHCP to Off.

    3. Enter the IP address, subnet mask, and gateway IP address.

  3. Select F10: Save.

  4. Select Esc to get back to the iLO 5 Configuration Utility, and then select User Management.

  5. Select Edit/Remove User. The administrator is the only default user defined.

  6. Change the default password and select F10: Save.

Set up the BIOS and RAID array

This procedure describes how to configure the BIOS configuration for an unconfigured sensor appliance. If any of the steps below are missing in the BIOS make sure that the hardware matches the specifications above.

HPE BIOS iLO is a system management software designed to give administrators control of HPE hardware remotely. It allows administrators to monitor system performance, configure settings, and troubleshoot hardware issues from a web browser. It can also be used to update system BIOS and firmware. The BIOS can be set up locally or remotely. To set up the BIOS remotely from a management computer, you need to define the HPE IP address and the management computer's IP address on the same subnet.

To configure the HPE BIOS:

  1. Select System Utilities > System Configuration > BIOS/Platform Configuration (RBSU).

  2. In the BIOS/Platform Configuration (RBSU) form, select Boot Options.

  3. Change Boot Mode to UEFI BIOS Mode, and then select F10: Save.

  4. Select Esc twice to close the System Configuration form.

  5. Select Embedded RAID 1: HPE Smart Array E208i-a SR Gen 10 > Array Configuration > Create Array.

  6. In the Create Array form, select all four disk options, and on the next page select RAID10.

Note

For Data-at-Rest encryption, see HPE guidance for activating RAID SR Secure Encryption or using Self-Encrypting-Drives (SED).

Install iLO remotely from a virtual drive

This procedure describes how to install iLO software remotely from a virtual drive.

Before installing the iLO software, we recommend changing the iLO idle connection timeout setting to infinite, as the installation might take longer than the 30 minutes it is set to by default, depending on your network connection and if the sensor is in a remote location.

To change the iLO idle connection timeout settings:

  1. Sign in to the iLO console, and go to Overview on the top menu.

  2. On the left, select Security, and then select Access settings from the top menu.

  3. Select the pencil icon next to iLO and then select Show advanced settings.

  4. On the Idle connection timeout row, select the triangle icon to open the timeout options, and then select Infinite.

Continue the iLO installation with the following steps.

To install sensor software with iLO:

  1. When signed into the iLO console, select the servers' screen on the bottom left.

  2. Select HTML5 Console.

  3. In the console, select the Virtual media CD icon on the right, and choose the CD/DVD option.

  4. Select Local ISO file.

  5. In the dialog box, choose the Defender for IoT sensor installation ISO file.

  6. Go to the left menu icon, select Power, and then select Reset.

  7. The appliance will restart, and run the sensor installation process.

Install Defender for IoT software on the HPE ProLiant DL20 Gen10 Plus

This procedure describes how to install Defender for IoT software on the HPE ProLiant DL20 Gen10 Plus.

The installation process takes about 20 minutes. After the installation, the system is restarted several times.

To install Defender for IoT software:

  1. Connect the screen and keyboard to the appliance, and then connect to the CLI.

  2. Connect an external CD or disk-on-key that contains the software you downloaded from the Azure portal.

  3. Start the appliance.

  4. Continue with the generic procedure for installing Defender for IoT software. For more information, see Defender for IoT software installation.

Next steps

Continue understanding system requirements for physical or virtual appliances. For more information, see Which appliances do I need?.

Then, use any of the following procedures to continue: