Muokkaa

Jaa


Configure routers for a Highly Available (HA) deployment

In a Highly Available Azure Private 5G Core deployment, the Azure Kubernetes Service (AKS) cluster runs on a two-node cluster of ASE devices. The ASE devices are deployed in an active / standby configuration, with the backup ASE rapidly taking over service in the event of a failure. Incoming traffic uses a virtual IP address which is routed to the active ASE's virtual network interface card (vNIC). Bidirectional Forwarding Detection (BFD) is used to detect failures.

This requires you to deploy a gateway router between the ASE cluster and:

  • the RAN equipment in the access network.
  • the data networks.

The following diagram shows an overview of a highly available deployment with a single access network router and a single data network router.

Diagram showing a highly available deployment with a single access network router and a single data network router.

The routers should rapidly detect the failure of an ASE device through a BFD session going down and immediately redirect all traffic to the other ASE. With the recommended settings, BFD should be able to detect failure in about one second, ensuring that traffic should be restored in less than 2.5 seconds. User plane state is replicated across the two ASEs to ensure the backup can take over immediately.

AP5GC only supports a single gateway router IP address per network. Therefore, only a network design where there is either a single gateway router per network or where the gateway routers are deployed in redundant pairs in an active / standby configuration with a floating gateway IP address is supported. The gateway routers in each redundant pair should monitor each other using VRRP (Virtual Router Redundancy Protocol) to provide detection of partner failure.

By default, the packet core creates a single BFD session with the gateway router IP address. For a redundant pair of routers, you must configure the packet core with the interface IP address of each router in addition to the shared gateway address. The packet core will then create an additional BFD session with each router. If one BFD session goes down due to a router failure, service is unaffected because the gateway address is still reachable from the other router. This configuration is added later when you create the site; see Collect the required information for a site for details. If you do not configure the interface IP addresses, it is possible for a router to forward traffic to an ASE device that cannot forward it on in the event of a port, link or top-of-rack switch failure.

The following diagram shows the physical layout of the access network with a redundant pair of routers. All links are in a single virtual local area network (VLAN) for the access network. The layout for each data network is similar.

Diagram showing the physical layout of the access network with a redundant pair of routers.

This how-to guide describes the configuration required on your router or routers to support an HA deployment. The gateway router for the access network and the gateway router for the data networks may be the same device or separate devices.

Prerequisites

Collect router configuration values

To determine how to configure the static routes on the gateway routers, navigate to your Packet Core Control Plane resource in the Azure portal. Under Settings, select Router configuration. This shows the N2S1 and N3 virtual IP addresses, the IP prefix for all UE pools for each data network and the next hops and relative priorities.

Configure the access network router

Configure the router in the access network with the following static routes. The IP addresses defined in the access network are described in private mobile network prerequisites.

Destination Prefix length Next hop Priority (lower values are more preferred)
Virtual N2 32 One of the IP addresses defined in the access network as vNIC addresses on the AMFs’ interfaces to the local access subnet. 10
Virtual N2 32 The other IP address defined in the access network as vNIC addresses on the AMFs’ interfaces to the local access subnet. 10
Virtual N3 32 The preferred IP address defined in the access network as one of the vNIC addresses on the UPFs’ interfaces to the local access subnet. 10
Virtual N3 32 The non-preferred IP address defined in the access network as one of the vNIC addresses on the UPFs’ interfaces to the local access subnet. 20

Configure BFD on the access network router

The access network router must be configured with the following BFD sessions:

  • Two BFD sessions between the access network router and the pair of AMF vNIC addresses.
  • Two BFD sessions between the access network router and the pair of UPF vNIC addresses in the access network.

BFD sessions on the access data network routers should be configured to use a polling interval of 330 ms. The maximum tolerable packet loss should be set to 3 packets (this is the default on most routers).

Configure the data network routers

If network address translation (NAT) is not enabled, configure the routers in each data network with the following static routes. For user plane traffic in the access network, one of the static routes is preferred to the other so that, in normal operation, all data network traffic uses the same route. Each data network supports a single subnet.

Destination Prefix length Next hop Priority (lower values are more preferred)
All UE subnets Variable DN preferred vNIC (vNIC addresses on the UPFs’ interfaces to the DN). 10
All UE subnets Variable DN preferred vNIC (vNIC addresses on the UPFs’ interfaces to the DN). 20

Configure BFD on the data network routers

Each data network router must be configured with two BFD sessions between the data network router and the pair of UPF vNIC addresses in that data network.

Next steps

Your network should now be ready to support a Highly Available AP5GC deployment. The next step is to collect the information you'll need to deploy your private network.