Muokkaa

Jaa


New-AcceptedDomain

This cmdlet is available only in on-premises Exchange.

Use the New-AcceptedDomain cmdlet to create an accepted domain in your organization. An accepted domain is any SMTP namespace for which an Exchange organization sends and receives email.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

New-AcceptedDomain
   [-Name] <String>
   -DomainName <SmtpDomainWithSubdomains>
   [-Confirm]
   [-DomainController <Fqdn>]
   [-DomainType <AcceptedDomainType>]
   [-WhatIf]
   [<CommonParameters>]

Description

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

New-AcceptedDomain -DomainName Contoso.com -DomainType Authoritative -Name Contoso

This example creates the new authoritative accepted domain Contoso.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-DomainController

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

The DomainController parameter isn't supported on Edge Transport servers. An Edge Transport server uses the local instance of Active Directory Lightweight Directory Services (AD LDS) to read and write data.

Type:Fqdn
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-DomainName

The DomainName parameter specifies the SMTP domain that you want to establish as an accepted domain. Valid input for the DomainName parameter is an SMTP domain. You can use a wildcard character to specify all subdomains of a specified domain, as shown in the following example: *.contoso.com.

However, you can't embed a wildcard character, as shown in the following example: domain.*.contoso.com. The domain name string may not contain more than 256 characters.

Type:SmtpDomainWithSubdomains
Position:Named
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-DomainType

The DomainType parameter specifies the type of accepted domain that you want to configure. Valid values are Authoritative, InternalRelay or ExternalRelay. You must set at least one value.

In an authoritative domain, messages are delivered to a recipient that has a domain account in your Exchange organization. In an internal relay domain, messages are relayed to a server outside your Exchange organization, but still under the authority of your company or IT department. Use the internal relay domain if you want to treat the messages to this domain as internal messages. In an external relay domain, messages are relayed to an email server, outside your organization, which you don't control.

The default value is Authoritative.

Type:AcceptedDomainType
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-Name

The Name parameter specifies a unique name for the accepted domain object.

Type:String
Position:1
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.