Muokkaa

Jaa


New-RoutingGroupConnector

This cmdlet is available only in Exchange Server 2010.

Use the New-RoutingGroupConnector cmdlet to establish a connection between a Microsoft Exchange Server 2010 routing group and an Exchange Server 2003 routing group when the organization is running more than one version of Exchange.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

New-RoutingGroupConnector
   [-Name] <String>
   -SourceTransportServers <MultiValuedProperty>
   -TargetTransportServers <MultiValuedProperty>
   [-BiDirectional <Boolean>]
   [-Confirm]
   [-Cost <Int32>]
   [-DomainController <Fqdn>]
   [-PublicFolderReferralsEnabled <Boolean>]
   [-WhatIf]
   [<CommonParameters>]

Description

The New-RoutingGroupConnector cmdlet creates a new routing group connector between the Exchange 2010 routing group and Exchange Server 2003 routing groups. A routing group connector is used to send and receive messages between computers that have the Exchange 2010 Hub Transport server role installed and Exchange 2003 bridgehead servers. The Exchange 2003 source servers specified in this cmdlet are automatically added to the ExchangeLegacyInterop universal security group. By default, the Exchange 2010 system grants Send to and Receive from permissions on the Hub Transport servers to the members of this group.

To create the routing group connector, you must specify the source servers from the originating routing group and the target servers in the destination routing group. The routing group connector is created in the routing group of which the source server is a member. By using the Bidirectional parameter, you can specify whether the connector is used for one-way or two-way mail flow. If you specify a two-way connector, a reciprocal connector is created in the target routing group. The source and target servers must be Exchange 2010 Hub Transport servers or Exchange 2003 bridgehead servers.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

New-RoutingGroupConnector -Name "Interop RGC" -SourceTransportServers "Hub2010.contoso.com" -TargetTransportServers "Bridgehead2003.contoso.com" -Cost 100 -Bidirectional $true

This example creates the routing group connector Interop RGC with the following properties:

  • The Exchange 2010 server is Hub2010.contoso.com.
  • The Exchange 2003 bridgehead server is Bridgehead2003.contoso.com.
  • The routing group connector is a two-way connector between the Exchange 2010 routing group and the routing group associated with the specified Exchange 2003 server.
  • The cost is 100.

Parameters

-BiDirectional

The BiDirectional parameter specifies whether this is a one-way or two-way connector. The default value is $false.

Type:Boolean
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

  • Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
  • Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
Type:SwitchParameter
Aliases:cf
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-Cost

The Cost parameter specifies a cost to the connector. Transport servers use the connector cost to determine the least cost routing path from a source server to the destination server for message delivery. The default value is 1.

Type:Int32
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-DomainController

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:Fqdn
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-Name

The Name parameter specifies the name to assign to the routing group connector.

Type:String
Position:1
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-PublicFolderReferralsEnabled

The PublicFolderReferralsEnabled parameter specifies whether users can use this routing group connector to access a public folder replica located in the routing group of the target servers when an instance of that public folder isn't available in the same routing group as the user's mailbox. The default value is $true.

Type:Boolean
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-SourceTransportServers

The SourceTransportServers parameter specifies the host name or fully qualified domain name (FQDN) of the transport servers used to send messages to the target transport servers. You can specify more than one server by separating each entry with a comma.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-TargetTransportServers

The TargetTransportServers parameter specifies the host name or FQDN of the transport servers that receive messages from the source transport servers. You can specify more than one server by separating each entry with a comma.

Type:MultiValuedProperty
Position:Named
Default value:None
Required:True
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:SwitchParameter
Aliases:wi
Position:Named
Default value:None
Required:False
Accept pipeline input:False
Accept wildcard characters:False
Applies to:Exchange Server 2010

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.