Load balance network traffic in an SDN fabric using VMM

You can use the Software Load Balancer (SLB) to distribute the network traffic evenly among the workloads in Software Define Networking (SDN) managed by the Cloud Service Providers (CSPs) and the tenants. For more information, see Software Load Balancer (SLB).

System Center Virtual Machine Manager (VMM) supports the following two scenarios of load balancing:

• Load balancing the external network traffic: This scenario includes load balancing the network traffic coming from an external network. Load balancing is done through a public Virtual IP (VIP). The workload VMs can be connected to a no isolation VM network or to a network virtualization enabled VM network.

• Load balancing the internal network traffic (Internal load balancing): This scenario includes load balancing the network traffic of workloads in the VM network that is enabled for network virtualization. Load balancing is done through a VIP.

  Note

  VMM supports configuration of load balancing by using PowerShell. Configuration through Service templates is currently not supported.

This article provides information about how to configure the load balancing of workload VMs by using PowerShell.

Before you start

Ensure the following:

• SDN network controller and the SDN software load balancer are deployed.

• Required VMs are created on appropriate networks and are identified for load balancing.

Create a VIP template

Use the following procedures to configure the VIPs to load balance the workload VMs (DIPs).

1. In the VMM console, select Fabric > VIP Templates. Right-click and select Create VIP Template.

   

2. In the Name page, provide the name and optional description. Specify the Virtual IP Port that will be used as front-end port for the network traffic. In the Backend port, specify the port on which the back-end workloads are hosted. Select Next.

   

3. In Type, under Specify a template type, select Specific. Select Microsoft from the Manufacturer dropdown and Microsoft Network Controller from the Model dropdown.

4. Select Next.

   

5. In Specify Protocol options, select the Custom option and TCP/UDP in Protocol name. Select Next.

   Note

   SLB supports only layer 4 load balancing of TCP/UDP traffic. HTTP/HTTPS protocols are not supported.

6. For Persistence and Load Balancing, use the defaults. Select Next.

   

   Note

   SLB doesn’t support persistence and different load balancing methods. By default, SLB uses Round Robin algorithm for load balancing.

7. In Health Monitors, optionally, insert appropriate values. Select Next.

   Options: TCP and HTTP are supported as health monitor protocols if SLB is used.

8. Verify the settings, and select Finish.

Once the template is created, you can find this under Fabric > VIP Templates.

Create a VIP using PowerShell

Create a VIP by using the following example scripts. Select the script based on the type of network traffic that you want to load balance:

• Script for creating a VIP to load balance external network traffic

• Script for creating a VIP to load balance internal network traffic

Script for creating VIP to load balance external network traffic

The following example script creates the VIP from a public IP network to load balance the workload VMs WGB-001 & WGB-002 on port 80.

This script can be used to create load balancing VIP by passing IPv6 VIP address as well.

The workload VMs can be connected to a no isolation network or network virtualization enabled VM networks.

Note

• In the script parameters section, substitute the actual values that match your test environment for the samples used in this script.
• Ensure that you run the script on a VMM server or on a computer running the VMM console.

param(

[Parameter(Mandatory=$false)]
# Name of the Network Controller Network Service
# This value should be the name you gave the Network Controller service
# when you on-boarded the Network Controller to VMM
$LBServiceName = "NC",

[Parameter(Mandatory=$false)]
# Name of the workload VMs you want to load balance.
$VipMemberVMNames =  @("WGB-001","WGB-002"),

[Parameter(Mandatory=$false)]
# Name of the VIP VM Network
$VipNetworkName = "PublicVIP",


[Parameter(Mandatory=$false)]
# VIP address you want to assign from the VIP VM Network IP pool.
# Pick any VIP that falls within your VIP IP Pool range.
$VipAddress = "44.15.10.253",


[Parameter(Mandatory=$false)]
# The name of the VIP template you created via the VMM Console.
$VipTemplateName = "WebsiteHTTP",

[Parameter(Mandatory=$false)]
# Arbitrary but good to match the VIP you're using.
$VipName = "scvmm_44_15_10_253_80"

)

Import-Module virtualmachinemanager

$lb = Get-scLoadBalancer | where { $_.Service.Name -like $LBServiceName};
$vipNetwork = get-scvmnetwork -Name $VipNetworkName;

$vipMemberNics = @();
foreach ($vmName in $VipMemberVMNames)
{
$vm = get-scvirtualmachine -Name $vmName;
#    if ($vm.VirtualNetworkAdapters[0].VMNetwork.ID -ne $vipNetwork.ID)
#    {
#        $vm.VirtualNetworkAdapters[0] | set-scvirtualnetworkadapter -VMNetwork $vipNetwork;
#    }

$vipMemberNics += $vm.VirtualNetworkAdapters[0];
}

$existingVip = get-scloadbalancervip -Name $VipName
    if ($existingVip -ne $null)
{
#    foreach ($mem in $existingVip.VipMembers)
#    {
#        $mem | remove-scloadbalancervipmember;
#    }

    $existingVip | remove-scloadbalancervip;
}

$vipt = get-scloadbalancerviptemplate -Name $VipTemplateName;

$vip = New-SCLoadBalancerVIP -Name $VipName -LoadBalancer $lb
-IPAddress $VipAddress -LoadBalancerVIPTemplate $vipt
-FrontEndVMNetwork $vipNetwork
-BackEndVirtualNetworkAdapters $vipMemberNics;
Write-Output "Created VIP " $vip;

$vip = get-scloadbalancervip -Name $VipName;
Write-Output "VIP created successfully " $vip;

Script for creating VIP to load balance internal network traffic

For the following example script, we created a new VIP template by name ILB-VIP-Template for load balancing the port 443 using the procedure detailed in the previous section. The script creates a VIP from tenant VM network to load balance the VMs ILB-001 & ILB-002, which are part of the same tenant VM network.

This script can be used to create load balancing VIP by passing IPv6 VIP address as well.

Note

• In the internal load balancing scenario, the VIP comes from the tenant VM network. So, the $VipNetworkName is the same tenant VM network name where the VMs are connected. Ensure that the tenant VM network IP pool has the IPs reserved for VIPs. The $VipAddress is one of the IP addresses from the reserved VIPs.
• In the script parameters section, substitute the actual values that match your test environment for the samples used in this script.
• Ensure that you run the script on a VMM server or on a computer running the VMM console.

param(

[Parameter(Mandatory=$false)]
# Name of the Network Controller Network Service
# This value should be the name you gave the Network Controller service
# when you on-boarded the Network Controller to VMM
$LBServiceName = "NC",

[Parameter(Mandatory=$false)]
# Name of the workload VMs you want to load balance.
$VipMemberVMNames =  @("ILB-001","ILB-002"),

[Parameter(Mandatory=$false)]
# Name of the VIP VM Network
$VipNetworkName = "TenantNetwork",

[Parameter(Mandatory=$false)]
# VIP address you want to assign from the VIP VM Network IP pool.
# Pick any VIP that falls within your VIP IP Pool range.
$VipAddress = "192.168.100.75",

[Parameter(Mandatory=$false)]
# The name of the VIP template you created via the VMM Console.
$VipTemplateName = "ILB-VIP-Template",

[Parameter(Mandatory=$false)]
# Arbitrary but good to match the VIP you're using.
$VipName = "scvmm_192_168_100_75_443"

)

Import-Module virtualmachinemanager

$lb = Get-scLoadBalancer | where { $_.Service.Name -like $LBServiceName};
$vipNetwork = get-scvmnetwork -Name $VipNetworkName;

$vipMemberNics = @();
foreach ($vmName in $VipMemberVMNames)
{
$vm = get-scvirtualmachine -Name $vmName;
#    if ($vm.VirtualNetworkAdapters[0].VMNetwork.ID -ne $vipNetwork.ID)
#    {
#        $vm.VirtualNetworkAdapters[0] | set-scvirtualnetworkadapter -VMNetwork $vipNetwork;
#    }

$vipMemberNics += $vm.VirtualNetworkAdapters[0];
}

$existingVip = get-scloadbalancervip -Name $VipName
if ($existingVip -ne $null)
{
#    foreach ($mem in $existingVip.VipMembers)
#    {
#        $mem | remove-scloadbalancervipmember;
#    }

$existingVip | remove-scloadbalancervip;
}

$vipt = get-scloadbalancerviptemplate -Name $VipTemplateName;

$vip = New-SCLoadBalancerVIP -Name $VipName -LoadBalancer $lb
-IPAddress $VipAddress -LoadBalancerVIPTemplate $vipt
-FrontEndVMNetwork $vipNetwork
-BackEndVirtualNetworkAdapters $vipMemberNics;
Write-Output "Created VIP " $vip;

$vip = get-scloadbalancervip -Name $VipName;
Write-Output " VIP created successfully " $vip;