Bendrinti naudojant

Overview

  • Straipsnis

Scenery Configuration File

The single scenery configuration file, Scenery.cfg, indicates where scenery files are located and whether to empty the cache upon exit.  It can also be used to exclude certain types of scenery.

See Also

Table of Contents

  • general
  • area
  • Basic Scenery Grid
  • The Exclude Property

The scenery configuration file resides in the root directory of ESP, and consists of general and area sections.

[general]

The [general] section applies to all scenery.

title The title of the configuration file. Title=FS9 World Scenery 
description The description of the contents of the file. Description=FS9 Scenery Data
clean_on_exit Set to True to delete all files from the Cache folder upon exiting, otherwise all files in the Cache folder are left where they are upon exiting. Clean_on_Exit=TRUE

[area.n]

The scenery area entries indicate where scenery is located. For each area, such as [Area.nnn], nnn is the scenery area entry number and must be unique. The properties of each area entry are as follows:

title The title of the area. This text will be shown under the Scenery Area column in the Scenery Library.

The entries of the form nnnn Base refer to folders containing the standard scenery for the world, based on a grid shown in the Basic Scenery Grid section.		 Default Terrain( Title=Default Terrain )
Default Scenery( Title=Default Scenery )

0000 Base( Title=0000 Base )
0001 Base( Title=0001 Base )

Africa( Title=Africa )
Asia( Title=Asia )

Amsterdam Aerial Photo( Title=Amsterdam Aerial Photo )
Anchorage Aerial Photo( Title=Anchorage Aerial Photo )

Global, Generic & Vehicle Libraries( Title=Global, Generic & Vehicle Libraries )
Propeller Objects( Title=Propeller Objects )

Addon Scenery( Title=Addon Scenery )
texture_id Texture_ID=0 and Texture_ID=1 are special settings that should not be changed.  Texture_ID=0 sets the global default texture directory to be searched if the requested texture cannot be found from the given path.  This is also the location of global textures that have no other directory to reside in.  Texture_ID=1 is the default terrain texture directory. Default Terrain( Texture_ID=1 )
remote A remote path to the scenery files. When using a remote path the scenery is copied from the path shown to a uniquely named folder created by the simulator.  The scenery files are then read from the new folder, a sub-folder of the Cache folder. Remote paths are very useful when reading scenery files from a location that cannot be accessed as quickly as the local hard drive, for example, from CD drives or a remote server.
The format of the path can be one of the three defined for local paths.
Only one of remote or local should be used.		 No examples.
local The local path to the scenery files. When using a local path the scenery is read directly from the path shown. Various formats for designating the path to the scenery can be used:
1. Drive:\path
For example: C:\MyScenery
2. [Volume]\path
For example,  [MySceneryCD]\MyScenery
3 \\Machine\share\path
For example, \\MyServer\MyScenery
Only one of remote or local should be used.		 Default Terrain( Local=Scenery\World )
Default Scenery( Local=Scenery\BASE )

0000 Base( Local=Scenery\0000 )
0001 Base( Local=Scenery\0001 )

Africa( Local=Scenery\AFRI )
Asia( Local=Scenery\ASIA )

Amsterdam Aerial Photo( Local=Scenery\Cities\Amsterd )
Anchorage Aerial Photo( Local=Scenery\Cities\Anchor )

Global, Generic & Vehicle Libraries( Local=Scenery\Global )
Propeller Objects( Local=Scenery\Props )

Addon Scenery( Local=Addon Scenery )
layer The layer  number is typically equal to the [area.nnn] number. Higher numbered layers have priority over lower numbered layers.  This number is shown in the simulation Scenery Library under the Priority column. Notice that add-on scenery has the highest layer number. Default Terrain( Layer=1 )
Default Scenery( Layer=2 )

0000 Base( Layer=3 )
0001 Base( Layer=4 )

Africa( Layer=99 )
Asia( Layer=100 )

Amsterdam Aerial Photo( Layer=109 )
Anchorage Aerial Photo( Layer=110 )

Global, Generic & Vehicle Libraries( Layer=131 )
Propeller Objects( Layer=132 )

Addon Scenery( Layer=138 )
active Set to True to indicate that the scenery should be rendered by default. This will be shown as enabled scenery in the Scenery Library. If this is set to False, a user will have to enable the scenery before it is rendered. Default Terrain( Active=TRUE )
The New South America( Active=FALSE )
required Set to True to indicate the folder is required and that the scenery entry cannot be deleted or turned off in the Scenery Library dialog. Default Terrain( Required=TRUE )
0000 Base( Required=FALSE )
exclude See The Exclude Property..

Basic Scenery Grid

For default scenery, the world is divided into a grid, as shown in the following diagram, and the scenery for each grid rectangle is stored in a separate folder, named rrcc Base, where rr is the row in the grid (from 0 to 7), and cc the column (from 0 to 11).

The Exclude Property

The exclude property is provided to exclude the default scenery, objects and/or navigational aids, in a given four-sided area from being displayed, or transmitted in the case of radio navigational aids. The exclude property affects only scenery areas with a lower layer number than the scenery area the exclude property is added to. For example, if the property is placed in layer 70, then only layers 69 and below will be affected.

The exclude property has the following syntax (the north, west, south, east ordering must be adhered to):

exclude=North Latitude,West Longitude, South Latitude, East Longitude, category list

Exclusion happens only in the specified rectangular area:

The latitude and longitude entries must be in the form of degrees or degrees and minutes.  You do not need to add the * or ' symbols to indicate degrees and minutes. The category determines which default scenery type you choose to exclude in the defined area.  There are four categories:

  1. objects      Excludes all default 3-dimensional buildings and objects as well as airports.
  2. vors          Excludes all default VOR and ILS navigational aids
  3. ndbs         Excludes all default NDB navigational aids.
  4. all             Excludes all default objects and navigational aids

You can include more than one category. The maximum size of an exclude area is 90 degrees of longitude and 45 degrees of latitude.

The following example excludes all scenery types except NDB navigational aids from a rectangular area 30 minutes of longitude by 30 minutes of latitude:

  • exclude=N45 30,W120,N45,W119 30,objects,vors

All latitude and longitude references use the WGS84 geoid.