Set-SecOpsOverridePolicy
This cmdlet is available only in the cloud-based service.
Use the Set-SecOpsOverridePolicy cmdlet to modify SecOps mailbox override policies to bypass Exchange Online Protection filtering. For more information, see Configure the advanced delivery policy for third-party phishing simulations and email delivery to SecOps mailboxes.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Set-SecOpsOverridePolicy
[-Identity] <PolicyIdParameter>
[-AddSentTo <MultiValuedProperty>]
[-Comment <String>]
[-Confirm]
[-DomainController <Fqdn>]
[-Enabled <Boolean>]
[-Force]
[-RemoveSentTo <MultiValuedProperty>]
[-WhatIf]
[<CommonParameters>] Description
You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
Set-SecOpsOverridePolicy -Identity SecOpsOverridePolicy -AddSentTo secops2@contoso.comThis example modifies the SecOPs mailbox override policy with the specified settings.
Parameters
-AddSentTo
The AddSentTo parameter specifies an entry to add to the existing list of SecOps mailbox email addresses. Groups are not allowed.
You can specify multiple values separated by commas.
| Type: | MultiValuedProperty |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-Comment
The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".
| Type: | String |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-Confirm
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
| Type: | SwitchParameter |
| Aliases: | cf |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-DomainController
This parameter is reserved for internal Microsoft use.
| Type: | Fqdn |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-Enabled
The Enabled parameter specifies whether the policy is enabled. Valid values are:
- $true: The policy is enabled. This is the default value.
- $false: The policy is disabled.
| Type: | Boolean |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-Force
The Force switch hides warning or confirmation messages. You don't need to specify a value with this switch.
You can use this switch to run tasks programmatically where prompting for administrative input is inappropriate.
| Type: | SwitchParameter |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-Identity
The Identity parameter specifies the SecOps override policy that you want to modify. You can use any value that uniquely identifies the policy. For example:
- Name
- Id
- Distinguished name (DN)
- GUID
| Type: | PolicyIdParameter |
| Position: | 0 |
| Default value: | None |
| Required: | True |
| Accept pipeline input: | True |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-RemoveSentTo
The RemoveSentTo parameter specifies an entry to remove from the existing list of SecOps mailbox email addresses. Groups are not allowed.
You can specify multiple values separated by commas.
| Type: | MultiValuedProperty |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |
-WhatIf
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
The WhatIf switch doesn't work in Security & Compliance PowerShell.
| Type: | SwitchParameter |
| Aliases: | wi |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Online |