Manage Windows Defender Application Control for Azure Stack HCI, version 23H2

บทความ
04/04/2024

Applies to: Azure Stack HCI, version 23H2

This article describes how to use Windows Defender Application Control (WDAC) to reduce the attack surface of Azure Stack HCI. For more information, see Manage baseline security settings on Azure Stack HCI, version 23H2.

Prerequisites

Before you begin, make sure that you have access to an Azure Stack HCI, version 23H2 system that is deployed, registered, and connected to Azure.

View WDAC settings via Azure portal

To view the WDAC settings in the Azure portal, make sure that you have applied the MCSB initiative. For more information, see Apply Microsoft Cloud Security Benchmark initiative.

You can Use WDAC policies to control which drivers and apps are allowed to run on your system. You can only view the WDAC settings via Azure portal. To manage the settings, see Manage WDAC settings with PowerShell.

Manage WDAC settings with PowerShell

Enable WDAC policy modes

You can enable WDAC during or after deployment. Use PowerShell to enable or disable WDAC after deployment.

Connect to one of the cluster nodes and use the following cmdlets to enable the desired WDAC policy in "Audit" or "Enforced" mode.

In this build release there are two cmdlets:

Enable-AsWdacPolicy - Affects all cluster nodes.
Enable-ASLocalWDACPolicy - Affects only the node on which the cmdlet is run.

Depending on your use case, you should run a global cluster change or a local node change.

This is useful when:

You started with default, recommended settings.
You must install or run new third party software. You can switch your policy modes to create a supplemental policy.
You started with WDAC disabled during deployment and now you want to enable WDAC to increase security protection or to validate that your software runs properly.
Your software or scripts are blocked by WDAC. In this case you can use audit mode to understand and troubleshoot the issue.

Note

When your application is blocked, WDAC creates a corresponding event. Review the Event log to understand details of the policy that's blocking your application. For more information, see the Windows Defender Application Control operational guide.

Switch WDAC policy modes

Follow these steps to switch between WDAC policy modes. These PowerShell commands interact with the Orchestrator to enable the selected modes.

Connect to your Azure Stack HCI node.
Run the following PowerShell command using local administrator credentials or deployment user (AzureStackLCMUser) credentials.

Important

Cmdlets that require to be signed in as deployment user (AzureStackLCMUser) need proper credentials authorization via the security group (PREFIX-ECESG) and CredSSP (when using remote PowerShell) or Console session (RDP).
Run the following cmdlet to check the WDAC policy mode that is currently enabled:
```
Get-AsWdacPolicyMode
```
This cmdlet returns Audit or Enforced Mode per Node.
Run the following cmdlet to switch the policy mode:
```
Enable-AsWdacPolicy -Mode <PolicyMode [Audit | Enforced]>
```
For example, to switch the policy mode to audit, run:
```
Enable-AsWdacPolicy -Mode Audit
```
Warning

The Orchestrator will take up to two to three minutes to switch to the selected mode.

Run Get-ASWDACPolicyMode again to confirm the policy mode is updated.

Get-AsWdacPolicyMode

Here's a sample output of these cmdlets:

PS C:\> Get-AsWdacPolicyMode
VERBOSE: Getting WDAC Policy Mode on Node01
VERBOSE: WDAC Policy Mode on Node01 is Enforced.
VERBOSE: Getting WDAC Policy Mode on Node01
VERBOSE: WDAC Policy Mode on Node01 is Enforced.

NodeName     PolicyMode
--------     ----------
Node01 	Enforced
Node01 	Enforced

PS C:\> Enable-AsWdacPolicy -Mode Audit
WARNING: Setting WDAC Policy to Audit Mode on all nodes. This will not protect your system against untrusted applications
VERBOSE: Action plan instance ID specified: 6826fbf2-cb00-450e-ba08-ac24da6df4aa
VERBOSE: Started an action plan 6826fbf2-cb00-450e-ba08-ac24da6df4aa to set WDAC Policy to Audit Mode.
6826fbf2-cb00-450e-ba08-ac24da6df4aa

PS C:\> Get-AsWdacPolicyMode
VERBOSE: Getting WDAC Policy Mode on Node01
VERBOSE: WDAC Policy Mode on Node01 is Audit.
VERBOSE: Getting WDAC Policy Mode on Node01
VERBOSE: WDAC Policy Mode on Node01 is Audit.

NodeName     PolicyMode
--------     ----------
Node01 	Audit
Node01	Audit

Create a WDAC policy to enable third party software

While using WDAC in enforcement mode, for your non-Microsoft signed software to run, build on the Microsoft-provided base policy by creating a WDAC supplemental policy. Additional information can be found in the public WDAC documentation.

Note

To run or install new software, you might need to switch WDAC to audit mode first (see steps above), install your software, test that it works correctly, create the new supplemental policy, and then switch WDAC back to enforced mode.

Create a new policy in the Multiple Policy Format as shown below. Then use Add-ASWDACSupplementalPolicy -Path Policy.xml to convert it to a supplemental policy and deploy it across nodes in the cluster.

Create a WDAC supplemental policy

Use the following steps to create a supplemental policy:

Before you begin, install the software that will be covered by the supplemental policy into its own directory. It's okay if there are subdirectories. When creating the supplemental policy, you must provide a directory to scan, and you don't want your supplemental policy to cover all code on the system. In our example, this directory is C:\software\codetoscan.
Once you have all your software in place, run the following command to create your supplemental policy. Use a unique policy name to help identify it.
```
New-CIPolicy -MultiplePolicyFormat -Level Publisher -FilePath c:\wdac\Contoso-policy.xml -UserPEs -Fallback Hash -ScanPath c:\software\codetoscan
```

Run the following cmdlet to modify the metadata of your supplemental policy:

# Set Policy Version (VersionEx in the XML file)
 $policyVersion = "1.0.0.1"
 Set-CIPolicyVersion -FilePath $policyPath -Version $policyVersion

 # Set Policy Info (PolicyName, PolicyID in the XML file)
 Set-CIPolicyIdInfo -FilePath c:\wdac\Contoso-policy.xml -PolicyID "Contoso-Policy_$policyVersion" -PolicyName "Contoso-Policy"

Run the following cmdlet to deploy the policy:

Add-ASWDACSupplementalPolicy -Path c:\wdac\Contoso-policy.xml

Run the following cmdlet to check the status of the new policy:

Get-ASLocalWDACPolicyInfo